Our experienced, fully certified team is familiar with a wide range of makes and models, so no matter what type of HVAC system you might have, if it’s not working as it should, we can help. We are committed to fast, accurate diagnosis and speedy, high-grade repairs that restore your HVAC system to full function. We make sure we leave your home as we find it and that you’re clear on what the problem is and what options there are for its resolution – this puts you in control of all the work we complete.
Excalibur Water Systems helps solve the water challenges around the globe with water solutions for any possible water concerns in: water hardness, filtration of any contaminant, bacteria removal and high purity water needs and also comes with a warranty of up to 20 years at no extra cost. The best warranty for the water treatment equipment industry.
The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.
If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
I have a 90% efficient forced air gas furnace and when it was installed 4 years ago the guy didn't hook up a fresh air intake pipe allowing the furnace to draw in air from the hallway(slab home). My question is there are two holes for intake and I need to know if I should use one for the intake and block off the other or does it require two pipes? There is already a 2 exhaust leading outside thru wall.

The time it takes to install an AC unit and the associated cost depends on the square footage of your home. Many homeowners spend between $3,677 to $7,151 for a contractor to put in a new central air system.A family with a 2,000-square-foot house that already has a forced-air heating unit can expect to pay $3,500 to $4,000 for a cooling system. If technicians don't need to make any changes to the duct-work, then the project should take them an average of two to three days.
Installation—Having your HVAC systems installed by a professional is extremely important to prevent any future problems or needless repairs. Our professionals at Service Experts Heating & Air Conditioning can also help you choose what size equipment is appropriate for your house. Selecting a system that is too large or small can impact efficiency and add to your energy bills.

When your furnace filter becomes dirty, dusty and clogged, you can expect some negative effects on your furnace efficiency and your indoor air quality. The forced air is supposed to get blown through the filter and the filter is supposed to trap any particles so they don’t end up in your air ducts and throughout the house. When the filter has trapped too many particles and it is clogged up, the air keeps blowing, but some of those trapped particles will end up in the system and your living space. Another effect is that the furnace has to work harder to get the same amount of air through that dirty filter, so your heating bills may go up.


The main purpose of your furnace filter is to ensure that none of the additional materials your fans pull back into the unit - such as hair and dust - actually damage the furnace or its parts. In the process, it also improves air quality in your home. Some annual inspections will include changing and cleaning this part of the unit. That said, you can also clean or change your furnace filteryourself. Costs for new filters range based on brand, but tend to be around $30.
When a family chooses to work with Brothers Plumbing Heating And Electric they will not be disappointed. We are able to work on a very tight schedule and we know just what it takes to service a furnace. There is no doubt about it, a family does well to look into Brothers Plumbing Heating and Electric because we are truly the best Aurora furnace repair company. To learn more about heating and cooling systems, just give this page a visit today!
Have you noticed that your A/C isn’t working as well as it could be? Perhaps there is an unexplained noise coming from the unit, or it doesn’t keep your home at the correct temperature. In these circumstances, a competitively priced repair is vital. It’s unlikely the problem will resolve on its own, so if you suspect there’s an issue, one call to us is all it takes.

Heating Repair Co

×