*We work on all brands: Adams, Aire-Flo, Amana, Arcoaire, Armstrong, Beutler, Bryant, Carrier, Centurion, Coleman, Comfortmaker, Cozy, Daikin, Day & Night, Dayton, Ducane, Emerson, Empire, Evcon, Fedders, Friedrich, Frigidaire, Fujitsu, Gaffers & Statler, General Electric, Gibson, Goldstar, Goodman, GMC, Haier, Heil, Honeywell, Intertherm, Janitrol, Kenmore, Lennox, Luxaire, Maytag, Mitsubishi, Payne, Rheem, Ruud, Samsung, Sanyo, Sears, Sharp, Spartan, Tappan, Tempstar, Thermal Solutions, Trane, Utica, Weatherking, Westinghouse, Whirlpool, Williams, York, and Zephyr.

If your AC doesn’t turn off when room temperature reaches the temperature set on the thermostat, the problem is generally occurring either at the thermostat or in the electrical system that runs the outside condensing unit. You can use the AC’s circuit breaker to shut off the unit, but that should not be a permanent solution—circuit breakers are not designed to be used like light switches.
If the AC doesn’t turn off, it may be time to clean the condensing unit. Dirty condenser coils won’t give off heat efficiently and will keep the unit running.  Another possibility: The contacts on the outdoor run relay may have welded together—something that can happen over time because of frequent electrical arcing at the relay. Before checking the run relay, turn off the power to the furnace and the condensing unit. Next, disassemble the relay and pry apart the contacts. This should do the trick until you buy a replacement—which you should do soon.
The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.
Brothers Plumbing, Heating, and Electric came to the rescue. Our furnace was operating erratically over the Thanksgiving holidays. Brothers made time for us during this busy heating season to address and fix the problem. The heating technician, Ron, was thorough in explaining every diagnostic step he was taking in solving the problem. We appreciate the excellent service he provided us.

Jacobs Heating and Air Conditioning is your trusted source for commercial and residential air conditioning and heating repair in the metro Portland, Beaverton and Vancouver, WA areas. We offer repair and maintenance services for major air conditioner brands including Carrier, Daikin, Venmar, Honeywell, Navien and Heat N Glo to keep you comfortable at home or work during the summer months.
"Gerardo was very professional and kept us informed of what he was doing and what was needed. Our house is now the warmest it has been since we purchased it 3 years ago! And all of this was done on a Saturday morning with below freezing temps! We are very thankful and will be using Gerardo of True Comfort again when have the money to replace the furnace altogether."
An electric furnace provides warmth by moving air over and through a series of coils. Ductwork and vents then distribute that air to the individual rooms in your home. Repair costs will depend on both the brand and the exact nature of the problem, but tend to be lower than some of the options above. That's because the units are small, and issues tend to be contained within the heating elements themselves. Expect to spend less than $300 on your electric furnace repair, depending on the exact problem.
​ Our air conditioning service, air conditioning repair, heating service in Bedford have set prices that depend on the job, not the time we invest into it. As soon as your heating system or air conditioner is diagnosed, you will be informed on the rate it will cost for the repair, before the repair has begun. We will honor that price, regardless of how long the repair takes.
 As a Carrier dealer, with a wide variety of products to choose from, we can keep your family healthy and feeling comfortable all year long. We carry a complete line of indoor comfort equipment with innovations that raise the standards of comfort and reliability, including air conditioners, heat pumps, gas furnaces, programmable thermostats, humidifiers, ductless split systems, air cleaners, ultra violet lights, ventilators and zoning products. Let the experts at A. Johnson Heating & Air help you customize a solution that's right for you. 

Mr Manns did a great job of explaining what he was doing. I learned some new things. One request: before using the hose, please ask to use it. In my particular case, the spicot is misbehaving. I have a particular method for turning it on/off to minimize aggravating the problem. So while there are no problems with him using it, I want to turn it on and off but was not given the opportunity to do so.


You should also have air ducts cleaned after recent water contamination or water damage to prevent mold; after renovations or remodeling to ensure debris and dust didn’t settle in the vents and ducts; if you are having problems with allergies or asthma; or when you are moving into a newly purchased home, especially if the previous owners smoked or had pets. The National Air Duct Cleaners Association (NADCA) recommends getting your air ducts cleaned every three to five years, or every two to three years in regions where homeowners use their air conditioning and heater for many months of the year, while the EPA suggests homeowners have duct cleaning done as needed.
Check the thermostat to see if the Fan switch has been turned on. If it has, turn it to OFF or to Auto. If it is set to OFF or Auto already, the heat pump’s limit switch needs to be adjusted. Call a heat pump repair technician to make the adjustment or, if you are handy with this type of repair, follow the instructions in your owner’s manual to reset the pointers on the fan side of the limit control. The lower pointer should be set to about 90 degrees F. and the upper one should be at about 115 degrees F.
High-efficiency condensing furnaces (90% AFUE and above) are a bit more complex than conventional furnaces. The main differences between a conventional and condensing furnace are the heat exchanger technology used to extract heat from the combustion process and the method used to exhaust the combustion gases. In these ways, the furnaces are very different. The condensing furnace does not have a significantly more efficient combustion process than does a conventional furnace; both use gas burners with electronic ignition. The difference lies in that the condensing furnace has a more efficient heat extraction process after combustion.

Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.


If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
The main purpose of your furnace filter is to ensure that none of the additional materials your fans pull back into the unit - such as hair and dust - actually damage the furnace or its parts. In the process, it also improves air quality in your home. Some annual inspections will include changing and cleaning this part of the unit. That said, you can also clean or change your furnace filteryourself. Costs for new filters range based on brand, but tend to be around $30.

Check your fuse box and make sure that your breaker is not flipped. If the breaker has been tripped, then no power will go to your system. Once you have switched it back on, check that there is power going to your thermostat, air handle, and outdoor HVAC unit. If you notice your breakers tripping regularly, then you may need to contact a qualified electrician.

If your compressor doesn’t have an overload button and you hear it humming or buzzing, poke a screwdriver or stick down through the top grille and try to spin the fan blades clockwise. If doing this gives the fan enough of a boost to get it going, the unit has a faulty capacitor that must be replaced. See How to Test and Replace an AC Run Capacitor, above.
Cleaning the debris that builds up on your filters will aid with the flow of air. When your air filter is clogged, your air handler must work harder to compensate for the blockage of air flow. In addition to driving up your utility bill, the reduced air flow through your heating and cooling system can cause your heat exchanger to overheat and shut off too quickly.    
Feel perfectly comfortable at home with our innovative Lennox Residential heating, cooling and air quality systems. Lennox manufactures high-efficiency HVAC systems including furnaces and air conditioners designed to conserve energy and save money. Our complementing air filtration systems, humidifiers and dehumidifiers help keep indoor air quality healthy and clean.
Expect exceptional service and superior quality. By consistently meeting rigorous national standards for performance, Deljo Heating & Cooling is distinguished as a Carrier Factory Authorized Dealer. We continue to reach high expectations for ethical business practices year after year. By maintaining all required local licenses, complete insurance & liability coverage, and fulfillment of warranty specifications, we provide Chicago area home and business owners a team of support they can count on.
Our goal is to make you more comfortable in your home. When your furnace, central air conditioner, heat pump or boiler stops working and you need service, call the professionals at BGE HOME. Heating and cooling system breakdowns occur at the most inconvenient times, so rely on our certified, skilled technicians to make the repair quickly and correctly the first time.
If the AC doesn’t turn off, it may be time to clean the condensing unit. Dirty condenser coils won’t give off heat efficiently and will keep the unit running.  Another possibility: The contacts on the outdoor run relay may have welded together—something that can happen over time because of frequent electrical arcing at the relay. Before checking the run relay, turn off the power to the furnace and the condensing unit. Next, disassemble the relay and pry apart the contacts. This should do the trick until you buy a replacement—which you should do soon.

"Very impressed. Returned call within 24 hours. They came out the same day I spoke with them and made the repair within 25 minutes. Very low service call fee. I had another repair service out two weeks earlier and after 3 service calls and the central air still not fixed and temperatures in the high 90's, it was such a relief to have a company identify the problem, have the necessary part with them and fix the problem."

HVAC Repair

×