You might guess it from the name: the heat exchanger is the part of your furnace that actually heats the air your blower motor pushes through the furnace. It consists of a chamber in which the heat energy produced by natural or propane gas is transferred to the forced air. At the same time, this part also includes a vent through which the gases themselves are safely removed from the unit and the air that enters your home. Because of these gases, a problem with your heat exchanger needs to be dealt with promptly. Over time, cracks in the exchanger can result in carbon monoxide leaks. Taking care of the problem once again means understanding the existence of a range: repairing your heat exchanger can cost as little as $100, but a full replacement may cost up to $1,200.


If the unit isn't turning on, check on it outside to make sure the condenser is still running. It should be fully plugged in and the thermostat should be set. Lower the thermostat by a few more degrees than your typical setting. You should hear it power on after doing so. If that doesn't take care of the problem, check your fuse box. You could have a blown fuse or a tripped circuit that's causing the air conditioner to not turn on.

I just finished fixing some skylights on my parent's house. They had the bubble type that started leaking after the roof was resurfaced. After investigating it carefully, it became apparent that when the roof was resurfaced, the edges of the skylight were covered with a sealant. (To help prevent leaks perhaps?)The problem was that this coating sealed up the weep slots along the perimeter of the aluminum frame. These slots are key to proper operation of the skylight. The skylight dome isn't sealed to the aluminum frame. The frame is designed with channels that direct any water that manages to flow between the bubble and the frame back out through weep holes.Make sure those weep holes are clear! They can be blocked by dirt, ice, or a well-intentioned roofer.
How often you should clean your air ducts depends on your situation. If you or someone in the home has asthma or is acutely allergic to certain airborne materials or pollen, regular duct cleaning may be helpful. The Environmental Protection Agency doesn’t have an official position on the necessity of air duct cleaning unless the ducts have been contaminated by rodents, insects or mold, or you are aware of particles blowing out through the vents. The EPA recommends you have your air ducts cleaned on an as-needed basis. The National Air Duct Cleaners Association (NADCA) suggests having air ducts cleaned every three to five years.
If your air ducts have been damaged, you’ll need to replace them. The national average air duct replacement cost is $150-$280, which may not include materials. Factors such as duct material, labor, location of ducts and linear feet of ductwork will all affect your final costs. Labor costs will vary based on how accessible the ducts are and what material your ducts are made of. The least expensive duct material is a flexible, non-metallic ducting that costs approximately $1-$2 per linear foot. Flexible aluminum is generally more expensive and stronger than non-metallic ducting. Stainless steel ducting is the strongest, the least flexible (meaning installing it typically has higher labor rates), and usually the most expensive. An average price for air duct replacement could range between $35 and $55 per linear foot, including basic materials and labor. A typical single-family home has 6-10 duct runs; replacing or installing one duct run could average $150-$250 for labor.
To reset a gas furnace, start by making sure the pilot light has been extinguished. Next, turn down the room thermostat to its coldest setting, and cut the furnace's power from your home's circuit breaker. Cut the main gas supply to the furnace, but make sure that the gas line that leads to the furnace pilot is on. Light a match, and use it to ignite the jet of the furnace's pilot flame. Then restore the furnace power and main gas supply, and press and hold the furnace reset button for roughly half a minute.
When our Denver heating company provides you with maintenance checks before the cold of winter sets in, you will be saving money in several different ways. One of the benefits of a maintenance plan is our technicians will be less likely to have to make repairs throughout the year as long as the system is properly maintained. Our Denver heating company will have your system running at its most efficient, helping to reduce your utility bills each month. An added benefit of a more efficiently running system is the positive environmental effect that it will have.

If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.


Hydronic heating is a newer technology that is water or liquid based and uses green technologies to heat or cool your home. Water (or an alternative liquid), is heated and then sent through a network of tubing or piping that sits under the floors. This system literally heats the floor, and the heat then rises up to heat the room. Imagine no more cold floors on those chilly winter mornings! Hydronic heating is an efficient method of delivering heat cheap and leaves no carbon footprint.
I'm looking about spanning 15' for a gazebo. trying to figure out what dimension beams I need. The Gazebo will be 15'x10'. How big will the beams have to be. at 1/2 the distance on 15' I will have a perpendicular beam running to carry 2x4's running parallel to 15' beam edge. I live in California in there with be no roofing material.. I will be using redwood for lumber Thanks
On average, furnace repair costs $287 nationally, with some homeowners spending as little as $60 while others paying $900 for furnace maintenance. Repairs to an electric furnace can run you $300 or less, while gas furnace repairs can be more complex and range from $375 to $1,200, depending on the what needs service. Most homeowners spend between $131 and $453 to fix their furnace. Here is what you need to know, along with the various factors that could affect the price of your furnace repair.
During the colder months of the year, the comfort of your home depends on the proper working function of your heating system. When your furnace breaks down or stops working properly, reach out to the heating experts at Horizon Services! We have nearly 30 years of experience providing reliable furnace repairs for homeowners throughout Delaware, Southern New Jersey, Southeastern Pennsylvania, and Northeastern Maryland. Our technicians are able to repair just about any type of home furnace using cutting-edge techniques and state-of-the-art tools. We can accurately diagnose the root of the issue and quickly get to work making the necessary repairs. We even offer same day service at no additional cost!

If your heat pump does not heat or cool properly, freezes up, or cycles off and on too frequently, this article can help. Following is step-by-step advice for troubleshooting typical heat pump problems and DIY heat pump repairs. Here we will deal with heat pump power problems; freezing up; improper heating, cooling, and cycling; blower issues; noises; and more. If these simple repair techniques don’t work, have a heat pump repair technician (go to HomeAdvisor) check out your system.
We have strived extremely hard to become the premier HVAC repair & installation choice for the peole of Columbia, Maryland. We pride ourselves on being the first HVAC company in all of Maryland to be awarded with Factory Authorized status. We have also earned the Distinguished Dealer Award by the Carrier Corporation for our strong & consistent dedication to superior local heating and air conditioning work in addition to exceptional customer satisfaction.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
×