Zolie from Brother's came out and repaired a main drain leak that was hidden and has been ongoing. He presented me with some options and recommendations and did an amazing, thorough job repairing the problem with the least invasive option. We are very grateful for our new relationship with Brothers and thankful for the work done by Zolie. THANK YOU!
A: When experiencing this problem, your first step should be changing the air filter and see if your furnace starts blowing warm air. DO NOT ignore this issue. Long term overuse will hurt your furnace heat exchanger, which is an expensive fix. Another possible option if you have a gas furnace is checking the pilot light to make sure it did not go out.
Acosta Heating & Cooling is your one-stop-shop for all of your indoor comfort needs. We’ve been serving the Charlotte area for over 45 years, and our customers are always treated with respect and professionalism. But with so many air conditioning and heating companies out there, how are you supposed to choose? It all starts with how a company treats their customers. Here at Acosta Heating & Cooling, you’ll always be treated like family. From a quick furnace repair to comprehensive air conditioning service, Acosta will always deliver. See below for some reasons why we’re the best air conditioning and heating service company in Charlotte and surrounding areas:
If you’re looking for a professional heating company in Denver with the proper experience to handle your project, our crew has many years of training and experience on most major heating systems available in the Denver area. Our heating company in Denver understands that in some situations, the scope of the damage may put the units beyond repair. In this instance, we can offer you help finding the right energy efficient model that will provide you warmth and savings in your wallet. Heating in Denver can be expensive during the coldest time of year, so choosing the right heating system can give the same amount of heat while at the same time providing big savings when our Denver heater repair technicians help you pick the right system for your home.
The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.
No one wants to be stuck in the dead of summer with a broken air conditioner, or in the cold of winter with a broken furnace or boiler. That’s why we’re available any time of day to make your emergency heating and air conditioning repair and get your system up and running as quickly as possible. We’ll show up on time, in uniform and ready to make your HVAC repair right the first time.
It isn’t unusual for a heat pump to ice-up in really cold weather, but it’s defrost cycle should kick on periodically to melt the ice. If the condenser unit of the heat pump is frozen up and the defrost cycle doesn’t melt the ice, turn it off. Make sure none of the return-air registers are blocked, and check the filter to make sure it isn’t clogged. If there doesn’t seem to be a problem with air flow to the unit, see more information at Heat Pump Cold Weather Problems or call an HVAC service professional.
AC units and thermostats have built-in delay features when they’re shut down and then repowered. The delay can be as long as 10 minutes. And, if you’ve subscribed to an energy-saving device from your local power utility, the unit can take even longer to reset. If you’ve installed the parts shown and reinstalled the disconnect block, repowered the circuit breaker, turned on the switch at the furnace, moved the thermostat to AC mode and lowered the temperature below the indoor temperature, and the unit doesn’t fire up after 30 minutes, it’s time to call a pro.
Replacing a capacitor is easy. Just take a photo of the wires before disconnecting anything (you may need a reference later on). Then discharge the stored energy in the old capacitor (Photo 4). Use needle-nose pliers to pluck one wire at a time from the old capacitor and snap it onto the corresponding tab of the new capacitor. The female crimp connectors should snap tightly onto the capacitor tabs. Wiggle each connector to see if it’s tight. If it’s not, remove the connector and bend the rounded edges of it so it makes a tighter fit on the tab. When you’ve swapped all the wires, secure the new capacitor (Photo 5).
Many homeowners don't often think of the state of their furnace—that is until, the first cold day of the year comes around and the furnace won't turn on or only blows cold air. Keeping an eye out for common signs of trouble can help you avoid a complete furnace breakdown. Addressing any issues early on can also help you avoid most extensive (and therefore, more expensive) repairs down the road.
"Warren at Lighten Up came in on time and as scheduled. Loved working with him. He provided new lighting for our kitchen remodel and did a great job. He still needs to come back and hook everything up. Also Seth came in and did some plumbing work and repair that we did not even know needed repair. I highly recommend this company and look forward to working with them in the future"
To reset a gas furnace, start by making sure the pilot light has been extinguished. Next, turn down the room thermostat to its coldest setting, and cut the furnace's power from your home's circuit breaker. Cut the main gas supply to the furnace, but make sure that the gas line that leads to the furnace pilot is on. Light a match, and use it to ignite the jet of the furnace's pilot flame. Then restore the furnace power and main gas supply, and press and hold the furnace reset button for roughly half a minute.
"Very impressed. Returned call within 24 hours. They came out the same day I spoke with them and made the repair within 25 minutes. Very low service call fee. I had another repair service out two weeks earlier and after 3 service calls and the central air still not fixed and temperatures in the high 90's, it was such a relief to have a company identify the problem, have the necessary part with them and fix the problem."