Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
I have a 90% efficient forced air gas furnace and when it was installed 4 years ago the guy didn't hook up a fresh air intake pipe allowing the furnace to draw in air from the hallway(slab home). My question is there are two holes for intake and I need to know if I should use one for the intake and block off the other or does it require two pipes? There is already a 2 exhaust leading outside thru wall.

This information is not intended as an offer to sell, or the solicitation of an offer to buy, a franchise. It is for information purposes only. Read More Currently, the following states regulate the offer and sale of franchises: California, Hawaii, Illinois, Indiana, Maryland, Michigan, Minnesota, New York, North Dakota, Oregon, Rhode Island, South Dakota, Virginia, Washington, and Wisconsin. If you are a resident of or want to locate a franchise in one of these states, we will not offer you a franchise unless and until we have complied with applicable pre-sale registration and disclosure requirements in your state. Read Less Aire Serv is a registered trademark of Aire Serv LLC © Aire Serv | All rights reserved | All Aire Serv franchise locations are independently owned and operated.

If your AC doesn’t turn off when room temperature reaches the temperature set on the thermostat, the problem is generally occurring either at the thermostat or in the electrical system that runs the outside condensing unit. You can use the AC’s circuit breaker to shut off the unit, but that should not be a permanent solution—circuit breakers are not designed to be used like light switches.
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
1 Be sure the thermostat is set to the proper setting (Heat if you’re calling for heat and the temperature you want the room to be). If the thermostat was replaced recently, the new thermostat may either be the wrong type (it must be specifically a heat pump thermostat) or it may have been wired improperly. A mistakenly wired thermostat can fry electronic components, preventing the heat pump from working properly.

If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.


1 Be sure the thermostat is set to the proper setting (Heat if you’re calling for heat and the temperature you want the room to be). If the thermostat was replaced recently, the new thermostat may either be the wrong type (it must be specifically a heat pump thermostat) or it may have been wired improperly. A mistakenly wired thermostat can fry electronic components, preventing the heat pump from working properly.
We’ve earned a reputation across Portland and The Dalles for dedicated customer service.  Consistently maintaining an A+ rating from the Better Business Bureau, Sky Heating & Air Conditioning meets higher standards of excellence through the little, important details that add up to a job well done.  It starts with a friendly voice on the phone, and the immediate focus of our extensive resources on your requirements.  From there, you can count on timely arrival, organized project management, careful cleanup, competitive pricing, and exemplary performance in every aspect of service.  When you contact Sky Heating & Air Conditioning for HVAC service in The Dalles and Portland, OR, your project is always handled by a highly-trained professional, who will achieve your goals for efficiency, reliability, and sustainable home comfort.

Zolie and Charely were very professional and on time.They gave us an estimate to replace our water heater and went over all our options.We opted to have them install a new water heater and get things up to code. Within three hours we had a new water heater installed. Zolie and Charley were efficient and pleasant to work with. We were pleased with the work that was completed!


At B & B Heating & Cooling, heating and cooling isn’t solely our job, it’s our passion. We’re dedicated to providing you with high quality HVAC service in Florissant. No matter the size of the problem or time of day, you can rely on us to get the job done properly. After all, B & B Heating & Cooling has been working in the community since 1985, bringing comfort to our customers right when they need it.

If you find yourself having a more traditional concern, we can help with that as well. Whether you’re looking to upgrade to a more energy efficient system, require an emergency furnace repair, or need to schedule an annual appointment, we’re here to help. We can tackle any issue or concern that you may have with your HVAC system. Our team will give you confidence and peace of mind when it comes to your HVAC system.
When a family chooses to work with Brothers Plumbing Heating And Electric they will not be disappointed. We are able to work on a very tight schedule and we know just what it takes to service a furnace. There is no doubt about it, a family does well to look into Brothers Plumbing Heating and Electric because we are truly the best Aurora furnace repair company. To learn more about heating and cooling systems, just give this page a visit today!
In addition to the information below, see these two articles for the general care and maintenance of your air conditioner: Preparing Your Air Conditioner for Summer and How to Replace Furnace & AC Filters. Most noteworthy, you should replace the filters at least twice a year, before the heating and cooling seasons. For information on furnace problems, please see Furnace Not Working.

Furnace Repair Co

×