Sky Heating & Air Conditioning provides a wide range of quality HVAC services to homeowners across Portland and The Dalles.  By bringing together skilled technicians and premier products, we deliver superior value for your investment.  We utilize tried and true strategies to enhance efficiency, comfort, and convenience throughout your home.  For heating and air conditioning installation, repair, and regular maintenance, no one takes better care of you than Sky Heating & Air Conditioning.  And we’re always here!  Count on us 24 hours a day, 7 days a week, to protect your safety, comfort, and best interests.

The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.
Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.
"Mike and crew were very prompt, very neat, and they quickly remedied the issue with our AC. Others, have tried to sell us on more than we actually needed. Mike was very honest about NOT replacing unnecessary parts. Superior was NOT the low bid, but they were close to it, and provided a very pleasant experience for this homeowner! I recommend you give Mike the opportunity address your Heating/AC issues and you can see for yourself why he has 5 Stars on all his reviews! Thanks Mike!"
As an Atlanta resident, you’re well aware that the weather in our area can go through extremes of both hot and cold throughout the year, taxing your heating and cooling system to its limits. You’ll likely encounter the need for repair or replacement at some point. If you need HVAC installation, HVAC maintenance, or HVAC service and repair, R.S. Andrews is the most trusted name in Atlanta.
Aurora residents are well aware that when the furnace goes out in their home, can be incredibly frustrating to get working again. At times, there are serious things that go wrong with a home that needs to get fixed very quickly. As far as the furnace goes, it needs to get repaired or fixed as soon as possible, which is why it’s good to know that our furnace repair company does furnace replacement in Aurora and also Aurora furnace repair, is prepared to help at any time. To learn more about our furnace and heating services, click HERE today!
The belt should slip right into place. If it seems to be too tight or difficult to set in place, it may be necessary to adjust the motor mount to provide more slack. Then you can re-tighten the tension once the belt is in place. Check the manufacturer’s specifications for proper tension—in most cases, the belt should deflect about an inch when you press down on it.
If you’re looking for a professional heating company in Denver with the proper experience to handle your project, our crew has many years of training and experience on most major heating systems available in the Denver area. Our heating company in Denver understands that in some situations, the scope of the damage may put the units beyond repair. In this instance, we can offer you help finding the right energy efficient model that will provide you warmth and savings in your wallet. Heating in Denver can be expensive during the coldest time of year, so choosing the right heating system can give the same amount of heat while at the same time providing big savings when our Denver heater repair technicians help you pick the right system for your home.
The chill of winter can be a scary thought when your furnace needs a repair. When the furnace in your home goes on the fritz, you need it fixed right away to keep your family safe and comfortable. Every BGE HOME technician is licensed in their trade and adheres to a stringent in-house certification program that guarantees their knowledge, affirms their commitment to the customer, and ensures excellence in completing every repair with the highest level of quality. Our technicians average 11 years in the HVAC industry, so you can rest assured that the technician who makes your furnace repair is knowledgeable and experienced.
Many things can go wrong with your furnace, all of which should be repaired and examined by experienced professionals. Trust Randazzo Heating, Cooling, and Fireplaces to repair and help you maintain your furnace*. We value our customers and their decisions, so we will always be honest and explain the best possible solution for you. Contact us today so we can help you out! Click Here for our warranty policy.
Has another company told you that your furnace has a cracked heat exchanger?  The heat exchanger is the heart of your furnace. Its failure can result in a dangerous situation for your home and the best solution is usually a new furnace.  Because of these issues, Bonney takes this situation very seriously.  We will offer you proof of the cracked heat exchanger in the form of a picture from our video inspection camera or a report from our exhaust gas analyzer, before we make our recommendation.
The cost of putting in a new heating system is going to depend on a variety of things. The square footage of your house is a big factor. How’s your home's insulation? What type of system are you planning to buy? Each system has its own hardware and installation variable, so price points will vary.   Are you converting to gas or oil? Add in the cost of running gas or oils lines to your house. Are you digging underground or is it all above ground, like solar? What system are you replacing? It’ll have to be removed and disposed of, so the more complicated or elaborate set up you have, the more it will cost to remove or install. Finally, you have to consider contractor fees. Luckily there are a lot of resources available to find quality candidates. To get a real idea of cost you will need to get estimates from contractors and/or full service hardware stores that sell and install systems.

Reinstall the access panel and disconnect block. Turn on the circuit breaker and furnace switch. Then set the thermostat to a lower temperature and wait for the AC to start (see “Be Patient at Startup,” below). The compressor should run and the condenser fan should spin. If the compressor starts but the fan doesn’t, the fan motor is most likely shot. Shut off the power and remove the screws around the condenser cover. Lift the cover and remove the fan blade and motor (photo 7). Reinstall the blade and secure the cover. Then repower the unit and see if the fan starts. If it doesn’t, you’ve given it your best shot—it’s time to call a pro.
Many homeowners don't often think of the state of their furnace—that is until, the first cold day of the year comes around and the furnace won't turn on or only blows cold air. Keeping an eye out for common signs of trouble can help you avoid a complete furnace breakdown. Addressing any issues early on can also help you avoid most extensive (and therefore, more expensive) repairs down the road.
Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.

The store scheduling was great - confirmed for an open date within minutes. My technician was thorough and patient in explaining and working through the resolve needed for my furnace problem. He was courteous and good-natured, which helped to calm my frazzled state over a unexpected HVAC repair. The tech took care in my home not to create or leave a mess. Finally, & more importantly, I felt that rate was fair and I didn't feel cheated at the end of it all. I was also pleased that I could put the expense on my Home Depot card. I'd rather not need it, but if I run into another problem, I would gladly use them again.

Heating Repair Company

×