Furnace breakdowns, no cooling when outside temperatures are soaring – heating and cooling repairs often catch us unexpectedly, making HVAC repair costs quite a surprise. Many homeowners worry when calling the HVAC repair contractor because of unexpected costs – your heating and cooling contractor won’t be able to give you a price for the repairs needed until he or she inspects the system to find the source of the problem.
In addition to providing repairs for A/C and HVAC systems, we can also repair almost any heating system. Just tell us what the trouble is and we will run the appropriate tests and checks to find out what needs doing to get your heating operational again. We use high-grade equipment and tools for every job we complete, helping to give you the top-quality results you’re looking for.
Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.
Vredevoogd Heating & Cooling technicians routinely assist our customers to figure out when it’s time to upgrade their Heating or Cooling system. Naturally, repairs are part of routine maintenance over the years. However, new models can save homeowners in a big way on energy expenses with their energy-efficient makeup. When you are ready to get a new system, we will do a careful check of your energy needs so that you can select the ideal system for your home’s needs. The wrong HVAC system for your home is a 15 year mistake that no one should have to afford. We install the right system for your home. Moreover, we offer guarantees that you won’t find just anywhere else. If your new installation isn’t right for your home, we’ll remove it free of charge at any time within that first year and refund 100% of your money. Our customers are burdened with no risks. We take on the risk because we are that sure of our expertise. We back our work with the strongest warranties in the field. In fact, we offer a wide array of warranties to provide you with the peace of mind you deserve as a valued Vredevoogd Heating & Cooling Grand Rapids MI customer.
If your compressor doesn’t have an overload button and you hear it humming or buzzing, poke a screwdriver or stick down through the top grille and try to spin the fan blades clockwise. If doing this gives the fan enough of a boost to get it going, the unit has a faulty capacitor that must be replaced. See How to Test and Replace an AC Run Capacitor, above.
A furnace flame sensor is a device that's found in the burner assembly of your home's furnace. This thin metal rod sits directly facing the furnace's flame stream, and it tells the furnace whether ignition has occurred once the gas valve has been opened. If the gas valve has been opened and the sensor fails to detect a flame, the furnace will automatically shut down.
If your AC doesn’t turn off when room temperature reaches the temperature set on the thermostat, the problem is generally occurring either at the thermostat or in the electrical system that runs the outside condensing unit. You can use the AC’s circuit breaker to shut off the unit, but that should not be a permanent solution—circuit breakers are not designed to be used like light switches.
Start with your utility company; they can help a great deal. Comparing previous bills isn't always a good measure, as the weather is never exactly the same month to month. Instead, if you take your energy bill and divide it by the square footage of livable space in your home, don't count areas like unfinished garages or basements -- you can calculate how much you are spending to heat or cool each square foot of your home. Your energy provider can tell you what the average cost per square foot is in your region for that same period of time so you can compare apples to apples.
I have a 90% efficient forced air gas furnace and when it was installed 4 years ago the guy didn't hook up a fresh air intake pipe allowing the furnace to draw in air from the hallway(slab home). My question is there are two holes for intake and I need to know if I should use one for the intake and block off the other or does it require two pipes? There is already a 2 exhaust leading outside thru wall.
If the condenser coils are clogged, the compressor can overheat and shut down. You’ll experience intermittent periods of minimal cooling, followed by no cooling. Even if you’re “sure” the condenser coils are clean, clean them again. Turn off the power. Flip the air conditioning service and furnace circuit breakers in your main electrical panel to the “Off” position. Next, turn off the power switch right at the furnace or air handler. Then yank the disconnect block (Photo 1) and clean the condenser coils (Photo 2). If the air conditioning service still doesn’t work properly after you’ve cleaned the condenser coils, installed a new filter and opened all the supply vents, proceed with the following repairs.
Trained to quickly and accurately make the diagnosis, our expert troubleshooters possess both the skills and speed that you need. Responding swiftly to your call, one of our technicians will provide you with a handwritten, fair and competitive estimate that details how exactly your system will be repaired. Offering a one-year parts and labor warranty, we restore your heat—and minimize your financial stress.
Check the thermostat to see if the Fan switch has been turned on. If it has, turn it to OFF or to Auto. If it is set to OFF or Auto already, the heat pump’s limit switch needs to be adjusted. Call a heat pump repair technician to make the adjustment or, if you are handy with this type of repair, follow the instructions in your owner’s manual to reset the pointers on the fan side of the limit control. The lower pointer should be set to about 90 degrees F. and the upper one should be at about 115 degrees F.
Excalibur Water Systems helps solve the water challenges around the globe with water solutions for any possible water concerns in: water hardness, filtration of any contaminant, bacteria removal and high purity water needs and also comes with a warranty of up to 20 years at no extra cost. The best warranty for the water treatment equipment industry.
Brothers Plumbing, Heating, and Electric came to the rescue. Our furnace was operating erratically over the Thanksgiving holidays. Brothers made time for us during this busy heating season to address and fix the problem. The heating technician, Ron, was thorough in explaining every diagnostic step he was taking in solving the problem. We appreciate the excellent service he provided us.
As a full-service heating contractor, we strongly encourage you to be vigilant with annual heating maintenance. Without proper maintenance, a heat pump, furnace or boiler might last only half as long as a well-maintained unit. Don’t tempt fate by skimping on annual service. We offer an economical, yet comprehensive maintenance agreement that we call our Cool Care Service Agreement. With our maintenance agreement you’ll receive:
"LIFESAVER! Came right out to our home to save us from the heat. I called around 11 and they sent someone by the afternoon 1:30. Carlos fixed our AC on the spot! Very professional and knew what the issues were and fixed them all as fast as possible! Otherwise we would all be toast in this Texas Summer HEat. Thank you Carlos with Ruben's AC! Excellent service"