Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.

Even if your air conditioning unit is still working, depending on the type of system in your home today, you could recoup your investment in a new system in as little as three years. However, that doesn't mean that your system needs to be replaced. Furnaces, air conditioners, and other heating and cooling systems have made tremendous gains in efficiency over the past five years, so if you have an older unit, it is worth taking a look at whether or not a repair is the best investment.
The contactor (relay) and start/run capacitor(s) (see illustration below) fail most often and are inexpensive. So it’s a safe bet to buy and install those parts right away, especially if your air conditioning service unit is older than five years. The condenser fan motor can also fail, but it runs about $150 — hold off buying that unless you’re sure that’s the culprit.
AC air handler squealing or grinding noises. Though most air handlers have direct-drive motors, some older units may be belt-driven. Squealing sounds from a belt-drive air handler generally occur when the belt that connects the motor to the blower slips. In most cases, the belt is improperly aligned or worn and needs replacement. Follow the instructions above under Air Conditioner Not Blowing Air and refer to your owner’s manual.
To reset a gas furnace, start by making sure the pilot light has been extinguished. Next, turn down the room thermostat to its coldest setting, and cut the furnace's power from your home's circuit breaker. Cut the main gas supply to the furnace, but make sure that the gas line that leads to the furnace pilot is on. Light a match, and use it to ignite the jet of the furnace's pilot flame. Then restore the furnace power and main gas supply, and press and hold the furnace reset button for roughly half a minute.
Fresh-Aire UV is an innovation leader in the field of indoor air quality. Our award-winning UV light and carbon products fight mold, bacteria, viruses and odors in commercial and residential HVACR systems. Our products include Blue-Tube UV®, the world’s most popular germicidal UV light, the revolutionary APCO® PCO/carbon whole-house air purifier, and Mini UV the first UV light system designed specifically for mini-split AC systems.
Have you noticed that your A/C isn’t working as well as it could be? Perhaps there is an unexplained noise coming from the unit, or it doesn’t keep your home at the correct temperature. In these circumstances, a competitively priced repair is vital. It’s unlikely the problem will resolve on its own, so if you suspect there’s an issue, one call to us is all it takes.
In addition to the information below, see these two articles for the general care and maintenance of your air conditioner: Preparing Your Air Conditioner for Summer and How to Replace Furnace & AC Filters. Most noteworthy, you should replace the filters at least twice a year, before the heating and cooling seasons. For information on furnace problems, please see Furnace Not Working.
Vredevoogd Heating & Cooling Grand Rapids MI routinely serves the areas of Grand Rapids, Wyoming, Lansing, Grandville, and Kalamazoo. We provide a comprehensive menu of HVAC services delivered by certified HVAC technicians who specialize in heating and cooling repair and installation. World-class customer service is a cornerstone of our business and we are committed to doing the job right the first time. We have a reputation for integrity and service excellence. By living up to our good name, we continue to build our customer base throughout the Michigan region and look forward to adding you to our service family. So if you are looking for a “heating & air company near me” in Grand Rapids, or a Furnace Repair Lansing, Furnace Repair Kalamazoo and more. Call today.
A furnace flame sensor is a device that's found in the burner assembly of your home's furnace. This thin metal rod sits directly facing the furnace's flame stream, and it tells the furnace whether ignition has occurred once the gas valve has been opened. If the gas valve has been opened and the sensor fails to detect a flame, the furnace will automatically shut down.
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
Sometimes a heating and air conditioning system just needs to be repaired rather than completely replaced. You may need air conditioning repair services if there is leaking around the outside unit, the air coming into the house isn't hot or cool enough, the unit is short-cycling or constantly turning on and off, using the system is consistently resulting in higher-than-normal energy bills, or if there is excessive noise during startup and operation.

©2018 By Horizon Services, LLC. All Rights Reserved. DE License # PL0000726, HL0000299. Contractor Reg. # PA017876, PA057742. NJ Plumbing Lic. # PL36BI01232300 - David Geiger HIC reg. # 13VH05117300, NJ Master HVACR contractor Lic. # 19HC00193700. MD Master HVACR contractor Lic. # 47186, MD Master Plumber/Gas Fitter Lic. # 63739 – David Geiger. EL.LIC./B.P. #34EI01207700.


At Comfort Plus Services, we set ourselves apart from the rest through quality customer service across Salisbury, MD and surrounding areas. See our Areas of Service. Our strength is in our high standards of job performance and fully trained professionals.  Our team upholds a proven reputation and is continually motivated to achieve excellence in every service we provide.
At B & B Heating & Cooling, heating and cooling isn’t solely our job, it’s our passion. We’re dedicated to providing you with high quality HVAC service in Florissant. No matter the size of the problem or time of day, you can rely on us to get the job done properly. After all, B & B Heating & Cooling has been working in the community since 1985, bringing comfort to our customers right when they need it.
Finally, don't underestimate the thermostat as a potential reason why your furnace is not working. Everything on the heating unit itself may function perfectly, but your home still will not heat right if the console you use to set the temperature doesn't communicate your input. A faulty thermostat can either be due to the wall unit itself, or the wiring that connects it to your furnace. Average thermostat repair costs are between $108 and $282, including labor. Replacement costs, of course, depend on the thermostat you choose. Visit our thermostat repair cost guide to learn more about this type of issue.
For almost 30 years, Horizon Services has been providing top-quality heating services for homeowners throughout Delaware, Southern New Jersey, Southeastern Pennsylvania, and Northeastern Maryland. Whether you need furnace repair, heat pump replacement, new system installation, or comprehensive maintenance for your home's heating system, you can rely on our skilled team to get the job done quickly and efficiently. Our technicians undergo some of the most rigorous technical training in the industry, including 150 mandatory hours of technical and customer service training every year, in order to equip them with the skills, tools, and experience to handle any heating need you may have. No matter the issue you're currently dealing with, we can quickly and correctly diagnose the source of the problem and get right to work resolving the matter at hand.
If you happen to live in a hot and humid area of the country, drainage problems can occur with your unit since moisture can trap itself inside the system. Routine maintenance can cut down on drainage issues by cleaning out any mold or algae from blocking the drain. If you notice moldy smells whenever you turn the thermostat down, check on your system.
Check your thermostat. First, ensure it is on the right setting. Is it set to “fan” by mistake? Second, check the location of your thermostat. Is there a heat source that could be affecting the reading? Is it located near a fan? If so, the your thermostat might be reading the temperature incorrectly. Investing in a Smart-thermostat is a great option, this will allow you to check & adjust your settings remotely.  
Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.

Call us today at (302) 200-4266 today to schedule a service heating system repair, replacement, installation, or tune-up services with our capable team! our team! We offer honest, upfront pricing in writing and industry leading warranties on parts and service. Find your local Horizon today to schedule heating system repair, replacement, installation, or tune-up services with our capable team!
×