You might guess it from the name: the heat exchanger is the part of your furnace that actually heats the air your blower motor pushes through the furnace. It consists of a chamber in which the heat energy produced by natural or propane gas is transferred to the forced air. At the same time, this part also includes a vent through which the gases themselves are safely removed from the unit and the air that enters your home. Because of these gases, a problem with your heat exchanger needs to be dealt with promptly. Over time, cracks in the exchanger can result in carbon monoxide leaks. Taking care of the problem once again means understanding the existence of a range: repairing your heat exchanger can cost as little as $100, but a full replacement may cost up to $1,200.
Our technicians explain all of your options before beginning the repair, so you can decide whether a repair or replacement is best for you. Our No Surprises Pricing—including charging by the job, not by the hour—means the price we quote you is the price you pay. If you decide that replacing your furnace is the best course of action, we can install a new, high-efficiency model in its place.
When you contract with Vredevoogd Heating & Cooling Grand Rapids MI, you can count on us to make safety our top priority. Your HVAC system is, of course, a major investment and integral to the functioning of your home; however, nothing is as important as the safety of each life within your home. We carefully inspect your system to ensure that it is functioning properly in order to guard against carbon monoxide poisoning or other system emergencies. We take the greatest care when installing your HVAC system, knowing that a perfect installation is the safest installation for your home. We follow our industry’s best practices concerning safety and will happily share our know how with you when it comes to safely maintaining your system between service appointments.  If you ever suspect a problem with your HVAC system, you hear strange noises or smell unpleasant odors, for instance, you can call us night or day, 24/7, to address your heating and cooling emergency. We’ll never leave you in the lurch! We are ready to provide service ASAP to ensure the safe operation of your HVAC system.
Central home air conditioner service systems consist of two major components: a condensing unit that sits outside your house, and the evaporator coil (often referred to as an A-coil) that sits in the plenum of your furnace or air handler. The refrigerant in the A-coil picks up the heat from your home and moves it to the outdoor condensing unit. The condensing unit fan blows outside air through the condensing coil to remove the heat. The condensing unit houses the three parts replaceable by a DIYer: the contactor, the start/run capacitor(s) and the condenser fan motor. The condensing unit also houses the compressor, but only a pro can replace that. The A-coil has no parts that can be serviced by a DIYer.
Solar heating is a method where the sun’s energy is collected by panels and converted to reusable energy. The sunlight collected is converted to direct current (DC) by photovoltaic cells in the panels. Then an inverter converts the DC current into alternating current (AC) and the panels send that electricity out and into your home to power things like your TV, computer, game consoles, and air conditioner. The more sunlight you have access to, the more energy you can produce. In some areas, solar powered homeowners can sell or trade the excess power they have accumulated to local power companies.
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​

If your AC doesn’t turn off when room temperature reaches the temperature set on the thermostat, the problem is generally occurring either at the thermostat or in the electrical system that runs the outside condensing unit. You can use the AC’s circuit breaker to shut off the unit, but that should not be a permanent solution—circuit breakers are not designed to be used like light switches.
If the condenser coils are clogged, the compressor can overheat and shut down. You’ll experience intermittent periods of minimal cooling, followed by no cooling. Even if you’re “sure” the condenser coils are clean, clean them again. Turn off the power. Flip the air conditioning service and furnace circuit breakers in your main electrical panel to the “Off” position. Next, turn off the power switch right at the furnace or air handler. Then yank the disconnect block (Photo 1) and clean the condenser coils (Photo 2). If the air conditioning service still doesn’t work properly after you’ve cleaned the condenser coils, installed a new filter and opened all the supply vents, proceed with the following repairs.
Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.
Having a company looking out for all your heating and cooling needs shouldn’t mean that you’re stuck with any run-of-the-mill shop who cuts corners. Heating and cooling has been our excitement since 1962, and it’s evident in the work we provide to our customers. We’re committed to providing you the very greatest when it comes to all things HVAC, whether it’s service, maintenance or heating and cooling systems.

You can help prevent issues with your system by scheduling routine maintenance on your furnace every year. During a maintenance visit, our technician will inspect and clean your furnace to help the system to run more smoothly and efficiently for the coming winter. You can have it done any time, but the maintenance is typically performed in the fall. Ask about our planned service agreement program!
Extensive training – Over the years, we have had to learn continually and update our skills to stay top-of-the-line. We continue to offer state-of-the-art products today with the service skills to match. We offer 800 hours of training classes to our technicians every year. They also have access to factory resource personnel and engineers for consultation.

Geothermal Heating and Cooling systems are unmatched in every way. This green alternative to temperature control is three times more efficient than conventional systems. Recognized by the US Environmental Protection Agency as the most environmentally-friendly option available today, installation of a geothermal HVAC system translates into a 50% reduction in heating costs, 30% reduction in cooling costs, and a 65% potential savings on hot water costs.  Sky Heating & Air Conditioning is now the largest WaterFurnace geothermal contractor west of Iowa. Our team of experienced professionals offer conscientious and skilled start-to-finish installation and service.  We specialize in outstanding geothermal HVAC systems, adding value and enjoyment to your home through sustainable solutions to year round temperature control. Contact Sky Heating & Air Conditioning for geothermal heat pump installation in Portland.

Ductwork pinging or popping. If you hear a pinging or popping sound coming from metal ductwork, this may be caused by thermal expansion or by air blowing past a loose flap of metal. Track along the duct runs, listening for the sound. If you find it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.
With colder weather on its way back to Waldorf, furnace and heating repair may not be the first thing you think about, but maybe it should be. Sure, it’s easy for us to sit here and tell you to schedule annual furnace service, but it’s only because we want to help you avoid a heating breakdown during the coldest day of the month in Waldorf. Day or night, our HVAC experts are here to make sure you have a comfortable home, and can help get your furnace back running in little time.
Looking for a local and trusted air conditioning and heater expert that is nearby? HVACs Today is here to help. Keeping your home or business heated or cooled is what we are great at. From installation to replacement and repairs, our technicians can complete your job quickly and correctly. Skilled contractors can solve your HVAC needs: no problem is too big or too small. Call us today to schedule your heating and cooling service.
In addition to the information below, see these two articles for the general care and maintenance of your air conditioner: Preparing Your Air Conditioner for Summer and How to Replace Furnace & AC Filters. Most noteworthy, you should replace the filters at least twice a year, before the heating and cooling seasons. For information on furnace problems, please see Furnace Not Working.
Interesting article but I feel you should give it more depth. When you write about foundations, you only mention poured concrete like there is no other type. Some houses have foundations made with brick, masonry block and less commonly stone. Same comment for roofing type. Never heard of a flat roof? Binoculars won't work for that type. Also, you should point out that the owner of a house can provide information that can't be directly observed like the age of a roof (but can be confirmed later with a home inspection).
Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.
You should also have air ducts cleaned after recent water contamination or water damage to prevent mold; after renovations or remodeling to ensure debris and dust didn’t settle in the vents and ducts; if you are having problems with allergies or asthma; or when you are moving into a newly purchased home, especially if the previous owners smoked or had pets. The National Air Duct Cleaners Association (NADCA) recommends getting your air ducts cleaned every three to five years, or every two to three years in regions where homeowners use their air conditioning and heater for many months of the year, while the EPA suggests homeowners have duct cleaning done as needed.
AC units and thermostats have built-in delay features when they’re shut down and then repowered. The delay can be as long as 10 minutes. And, if you’ve subscribed to an energy-saving device from your local power utility, the unit can take even longer to reset. If you’ve installed the parts shown and reinstalled the disconnect block, repowered the circuit breaker, turned on the switch at the furnace, moved the thermostat to AC mode and lowered the temperature below the indoor temperature, and the unit doesn’t fire up after 30 minutes, it’s time to call a pro.

If the unit isn't turning on, check on it outside to make sure the condenser is still running. It should be fully plugged in and the thermostat should be set. Lower the thermostat by a few more degrees than your typical setting. You should hear it power on after doing so. If that doesn't take care of the problem, check your fuse box. You could have a blown fuse or a tripped circuit that's causing the air conditioner to not turn on.

In the event of an emergency with your residential heating and cooling system, we understand that you simply cannot wait! At R.S. Andrews, we take your comfort and well-being seriously and are proud to offer our emergency HVAC repair at any hour, on any day—including weekends! We provide only the highest quality services to ensure your needs are met!
Interesting article but I feel you should give it more depth. When you write about foundations, you only mention poured concrete like there is no other type. Some houses have foundations made with brick, masonry block and less commonly stone. Same comment for roofing type. Never heard of a flat roof? Binoculars won't work for that type. Also, you should point out that the owner of a house can provide information that can't be directly observed like the age of a roof (but can be confirmed later with a home inspection).

Vredevoogd Heating & Cooling technicians routinely assist our customers to figure out when it’s time to upgrade their Heating or Cooling system. Naturally, repairs are part of routine maintenance over the years. However, new models can save homeowners in a big way on energy expenses with their energy-efficient makeup. When you are ready to get a new system, we will do a careful check of your energy needs so that you can select the ideal system for your home’s needs. The wrong HVAC system for your home is a 15 year mistake that no one should have to afford. We install the right system for your home. Moreover, we offer guarantees that you won’t find just anywhere else. If your new installation isn’t right for your home, we’ll remove it free of charge at any time within that first year and refund 100% of your money. Our customers are burdened with no risks. We take on the risk because we are that sure of our expertise. We back our work with the strongest warranties in the field. In fact, we offer a wide array of warranties to provide you with the peace of mind you deserve as a valued Vredevoogd Heating & Cooling Grand Rapids MI customer.
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​

Advice you can count on – When you have an emergency, you are not always in the position of asking questions to determine if the repairs you are receiving are what you need. At Jennings, our NATE Certified technicians will walk you through the repairs and explain why you need them. You can trust that everyone on Jennings’ staff will give you honest advice.


If your home is not heated using forced air, chances are a boiler will make sure you stay warm during cold nights. A hot water system delivers hot water through a network of pipes that run to every room in your house. The heating effect gets maximized through radiators. The most common issues with hot water heating tend to be not be major, but small problems that add up over time. Mineral deposits within the water tank, a pilot light malfunction, or an issue with a radiator itself can require professional repair. On average, you will pay between $183 and $582 for these problems. The exact amount will depend on the exact problem, as described in our boiler repair cost guide.
As a Bryant Factory Authorized Dealer, Cool Care Heating & Air installs durable, high-quality heating systems that will go the distance. Are you considering a heater installation or heating repair? If so, you have found the best HVAC dealer in the Columbia, SC area. We specialize in high-efficiency furnaces, heat pumps and boilers that can cut energy costs month after month.
At Knoechel Heating Company, heating and cooling isn’t just our job, it’s our passion. We’re dedicated to providing you with the top HVAC service in Zelienople. No matter the time, day or the problem, you can count on us to get the job done right. After all, Knoechel Heating Company has been servicing the community since 1947, bringing comfort to our customers all year round.
At Knoechel Heating Company, heating and cooling isn’t just our job, it’s our passion. We’re dedicated to providing you with the top HVAC service in Zelienople. No matter the time, day or the problem, you can count on us to get the job done right. After all, Knoechel Heating Company has been servicing the community since 1947, bringing comfort to our customers all year round.
Repairs—If something appears to be not working right with your heating and cooling, a professional will examine the whole health of your system. It’s easy to hop on the internet and research information to find our own conclusions, but there could be an additional component or reason why your system isn’t working properly that isn’t clear or recognizable. Consider our own health concerns—you might check out your symptoms online to try and draw your conclusions, but it’s always best to make an appointment with a doctor to receive an expert opinion.
If you’re looking for a professional heating company in Denver with the proper experience to handle your project, our crew has many years of training and experience on most major heating systems available in the Denver area. Our heating company in Denver understands that in some situations, the scope of the damage may put the units beyond repair. In this instance, we can offer you help finding the right energy efficient model that will provide you warmth and savings in your wallet. Heating in Denver can be expensive during the coldest time of year, so choosing the right heating system can give the same amount of heat while at the same time providing big savings when our Denver heater repair technicians help you pick the right system for your home.
Nothing is worse than having your furnace fail on the coldest night of the year. When your furnace needs a repair, you shouldn’t have to worry about the company providing your furnace repair services. You won’t have to – not when you give John Betlem Heating & Cooling a call. No matter what kind of furnace you own, our talented team of technicians are able to easily identify any problem your furnace might be having.
As a Bryant Factory Authorized Dealer, Cool Care Heating & Air installs durable, high-quality heating systems that will go the distance. Are you considering a heater installation or heating repair? If so, you have found the best HVAC dealer in the Columbia, SC area. We specialize in high-efficiency furnaces, heat pumps and boilers that can cut energy costs month after month.
When the time comes to schedule furnace repairs, you want a team you can trust. Keeping your home warm and comfortable is important for you and your family, which is why you should rely on the highly-trained team of technicians at Horizon Services. Our techs undergo at least 150 hours of technical training every year and are up-to-date on the latest, most advanced techniques in the trade. We also background-check all of our employees to ensure your complete comfort and safety. When you call on us for furnace repair, we will arrive on-time and on schedule, ready to resolve the issue as quickly as possible.
At Genz-Ryan, we are here for you 24 hours a day, 7 days a week so you can count on us for all your heating repair work in the Minneapolis area. Our furnace repair technicians are well-trained and experienced. They’re ready to take care of any heating issue that you may have. We are a Lennox Premier Furnace Dealer and provide expert furnace repair service for most of the Minneapolis/St. Paul area. For over 60 years we have been getting the job done right the first time.

"Very impressed. Returned call within 24 hours. They came out the same day I spoke with them and made the repair within 25 minutes. Very low service call fee. I had another repair service out two weeks earlier and after 3 service calls and the central air still not fixed and temperatures in the high 90's, it was such a relief to have a company identify the problem, have the necessary part with them and fix the problem."

HVAC Repair

×