If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
Coolray & Mr. Plumber have Smyrna, GA covered when it comes to air conditioning repair and installation, furnace repair and installation, plumbing service and more. We also offer a full range of HVAC and plumbing products to help meet the needs of Smyrna homeowners and businesses. We have been serving Smyrna, GA residents since 1966 and our HVAC technicians and plumbers have the experience and training to properly resolve all of your heating, cooling and plumbing issues. Our products include furnaces, air conditioners, heat pumps, geothermal HVAC systems, traditional water heaters, tankless water heaters, sump pumps, air cleaners & air purifiers and more. 
At A-PLUS Service Experts Heating & Air Conditioning, we are well accustomed heating and air conditioning, which is why we back up our work with our 100% Satisfaction Guarantee*. Not only does it demonstrate our confidence that you’ll be happy with the furnace repair we have finished, it holds us to a higher standard, making certain that we continue to provide you with exceptional service without fail. When it’s time to address any heating and cooling question or concern you have, know that you can trust the experts at A-PLUS Service Experts Heating & Air Conditioning regardless of what the Waldorf weather tosses our way.
The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.

HVAC Repair Co


Today’s heaters are technological wonders that will keep you warm and save you money. Investing in an energy-efficient heating system can raise the value of your property, and the cost of installation will be realized on the amount you’ll save on utility bills. With Cool Care Heating & Air, you can count on proper sizing and a hassle-free installation process. The new unit may also qualify for energy-efficient incentives, and Cool Care Heating & Air offers periodic dealer rebates on select replacement systems. If your heating system is 10-15 years old, needs frequent repair work and isn’t keeping you as warm as it used to, it’s probably approaching the end of its lifespan. Replacing the unit before it dies altogether can save you time, trouble and money.
When your heating or cooling system finally breaks, it’s not usually during convenient office hours or in mild weather. Your HVAC unit has to work harder during extreme conditions like a sweltering summer day or freezing winter night, so it is much more likely to fail during those times. R.S. Andrews has our customers’ safety and comfort as our priority, so we offer service 24 hours a day for emergencies. No matter when your equipment fails, you can count on us for 24-hour AC repair and heating repair!
The cost to replace your gas furnace will vary based on the type and size of furnace you select, labor and installation costs, and any repairs your HVAC system may need. Nationally, average HVAC prices for a heating specialist range between $1,800 and $2,500. It’s important to select the right size gas furnace for your heating needs. A furnace that’s too small won’t heat your house properly, while a furnace that’s too large will run inefficiently, cycling on and off and likely breaking down sooner. HVAC specialists calculate your exact heat needs by measuring your home and incorporating variables such as the regional climate and your home’s level of insulation. Retail pricing for gas furnaces can range from $650 up to $3,000 and more. The higher the AFUE (annual fuel utilization efficiency) rating of the furnace, the more efficient it is at turning fuel into heat and the lower your carbon footprint and utility bill will be. HVAC installation costs are often based on an hourly rate and can range from under $50 to over $100 per hour, depending on the company and the furnace being installed. Higher-end furnaces cost more to install because they require added labor and expertise. For a typical installation, it might take two HVAC installation pros one day or less to remove your old furnace and replace it with a new one.

As a full-service heating contractor, we strongly encourage you to be vigilant with annual heating maintenance. Without proper maintenance, a heat pump, furnace or boiler might last only half as long as a well-maintained unit. Don’t tempt fate by skimping on annual service. We offer an economical, yet comprehensive maintenance agreement that we call our Cool Care Service Agreement. With our maintenance agreement you’ll receive:
Yes. You should expect to pay a diagnostic fee to cover the cost of the technician's visit, the diagnosis of your air conditioner's problem, and a quote for the repair options. You will be advised of the issue along with recommended options to correct it, which may include a system replacement if your unit is old or significantly damaged. If you decide to replace the system, the diagnostic fee will be credited toward your replacement purchase.
Restoring or replacing an aging unit can get expensive. Invest in a new model if your utility bills are rising and you notice uneven air flow and temperatures throughout your property. If one room is cooler than another, consider a total replacement. If the air conditioner is relatively new and still within its age range, it's more cost-effective to get a contractor to repair it.
An electric furnace provides warmth by moving air over and through a series of coils. Ductwork and vents then distribute that air to the individual rooms in your home. Repair costs will depend on both the brand and the exact nature of the problem, but tend to be lower than some of the options above. That's because the units are small, and issues tend to be contained within the heating elements themselves. Expect to spend less than $300 on your electric furnace repair, depending on the exact problem.
When a family chooses to work with Brothers Plumbing Heating And Electric they will not be disappointed. We are able to work on a very tight schedule and we know just what it takes to service a furnace. There is no doubt about it, a family does well to look into Brothers Plumbing Heating and Electric because we are truly the best Aurora furnace repair company. To learn more about heating and cooling systems, just give this page a visit today!

We are open from 7am to 10pm every weekday and from 7am to 8pm on weekends. We book appointments in a 2 hour arrival window and call 30-45 mins before we arrive so you do not have to sit around waiting. It is often possible to schedule your appointment in the evening or morning hours to avoid conflicting with your work schedule. Are you looking for service today? Give us a call or click on one of the Schedule Service buttons found on the top and left sides of this page to contact us today.


Service Experts Heating and Air Conditioning was founded with the determination of delivering customers with the most excellent heating and cooling practices in the industry. Since its inception, A-PLUS Service Experts Heating & Air Conditioning in Waldorf has been devoted to our area, offering the first class HVAC (Heating, Ventilation, Air Conditioning) products and services in the area. If you would like to more information about your regional HVAC leaders, simply dial us at 301-747-3140 or set up an appointment with us using our online form.
We install heating equipment from Lennox and can repair all major brands, including Carrier, Trane, York, Bryant, Rheem, and many more. We proudly offer same day service and next day installations. Dealing with a heating emergency? We've got you covered! Our team is prepared to assist you 24 hours a day, 7 days a week to ensure that your home remains comfortable and safe for you and your family members.
Natural gas furnaces operate similarly to the above, using a pilot light to ignite the burners and heat up the air. Also similar to propane gas, your average repair costs for a natural gas furnace will range anywhere from $125 for small repairs to $1,200 if you have to replace the entire heat exchanger. The difference between both options is not necessarily the actual furnace, but the type of gas used to burn through it and heat your home. As a result, the repair costs tend to be close to identical.
For more than 30 years, Northeastern PA homeowners have trusted T.E. Spall & Son for heating, air conditioning, and plumbing in Scranton, Wilkes-Barre, and the surrounding areas. Our team of highly trained, professional HVAC contractors and plumbers is committed to providing you with the best heating and cooling services possible. Your satisfaction and comfort are always our number one priorities!

If your home is not heated using forced air, chances are a boiler will make sure you stay warm during cold nights. A hot water system delivers hot water through a network of pipes that run to every room in your house. The heating effect gets maximized through radiators. The most common issues with hot water heating tend to be not be major, but small problems that add up over time. Mineral deposits within the water tank, a pilot light malfunction, or an issue with a radiator itself can require professional repair. On average, you will pay between $183 and $582 for these problems. The exact amount will depend on the exact problem, as described in our boiler repair cost guide.
Solar heating is a method where the sun’s energy is collected by panels and converted to reusable energy. The sunlight collected is converted to direct current (DC) by photovoltaic cells in the panels. Then an inverter converts the DC current into alternating current (AC) and the panels send that electricity out and into your home to power things like your TV, computer, game consoles, and air conditioner. The more sunlight you have access to, the more energy you can produce. In some areas, solar powered homeowners can sell or trade the excess power they have accumulated to local power companies.
"Superior AC & Heat inspected my furnace on Monday and determine that I needed to replace the furnace. Since I was also desiring to add AC to my home, I decided to bundled both projects and get a new furnace and AC Unit together. The team arrive at my home Wednesday morning at 7:45 am; the new furnace was installed by 1:00 pm and they completed the AC Unit, tested it and cleaned up by 4:30 pm. Great work; I highly recommend them."
No one wants to be stuck in the dead of summer with a broken air conditioner, or in the cold of winter with a broken furnace or boiler. That’s why we’re available any time of day to make your emergency heating and air conditioning repair and get your system up and running as quickly as possible. We’ll show up on time, in uniform and ready to make your HVAC repair right the first time.

I just finished fixing some skylights on my parent's house. They had the bubble type that started leaking after the roof was resurfaced. After investigating it carefully, it became apparent that when the roof was resurfaced, the edges of the skylight were covered with a sealant. (To help prevent leaks perhaps?)The problem was that this coating sealed up the weep slots along the perimeter of the aluminum frame. These slots are key to proper operation of the skylight. The skylight dome isn't sealed to the aluminum frame. The frame is designed with channels that direct any water that manages to flow between the bubble and the frame back out through weep holes.Make sure those weep holes are clear! They can be blocked by dirt, ice, or a well-intentioned roofer.
Hello, We have a Hunter ceiling fan that no longer spins. It has power, as the light still works and when you push the remote you hear the clicking, like it's trying to engage, but the blades do not spin. Does this sound like a possible flywheel issue? I removed the Remote Receiver, part 85112-02, and apparently it's no longer available, but I don't think the receive is the problem. Any feedback would be welcome.
Cut down on energy costs and prevent damage to your furnace by addressing a gas furnace that's overactive or short cycling. Besides the need for consistently comfortable temperatures, this issue could cause long-term safety issues to your home, making it very important to address. From a faulty thermostat to a dirty filter, there are several possible causes to investigate.

Extensive training – Over the years, we have had to learn continually and update our skills to stay top-of-the-line. We continue to offer state-of-the-art products today with the service skills to match. We offer 800 hours of training classes to our technicians every year. They also have access to factory resource personnel and engineers for consultation.
Start with your utility company; they can help a great deal. Comparing previous bills isn't always a good measure, as the weather is never exactly the same month to month. Instead, if you take your energy bill and divide it by the square footage of livable space in your home, don't count areas like unfinished garages or basements -- you can calculate how much you are spending to heat or cool each square foot of your home. Your energy provider can tell you what the average cost per square foot is in your region for that same period of time so you can compare apples to apples.
Your furnace's flame sensor is essentially a safety mechanism. As a thin metallic rod in front of the flame inside the unit, it's sole purpose is to confirm that your gas valves only open when a flame actually exists to burn that gas. When the flame sensor stop working, on the other hand, gas leaks can occur. To repair your furnace's flame sensor, expect to spend between $80 and $250. Even a full replacement of this part typically does not go above that range.
AC units and thermostats have built-in delay features when they’re shut down and then repowered. The delay can be as long as 10 minutes. And, if you’ve subscribed to an energy-saving device from your local power utility, the unit can take even longer to reset. If you’ve installed the parts shown and reinstalled the disconnect block, repowered the circuit breaker, turned on the switch at the furnace, moved the thermostat to AC mode and lowered the temperature below the indoor temperature, and the unit doesn’t fire up after 30 minutes, it’s time to call a pro.
Nothing is worse than having your furnace fail on the coldest night of the year. When your furnace needs a repair, you shouldn’t have to worry about the company providing your furnace repair services. You won’t have to – not when you give John Betlem Heating & Cooling a call. No matter what kind of furnace you own, our talented team of technicians are able to easily identify any problem your furnace might be having.
Repair Clinic’s gas furnace troubleshooting guide will walk you through the steps necessary for diagnosing your furnace problem. Start with our list of symptoms. When you find the right one, we’ll show you the common causes. Enter your model number into the search field and you’ll know which part to buy. We can even show you how to install it. Where else can you find online furnace troubleshooting help like this?
For most homeowners, any HVAC repair needs to be done in a timely manner. The longer you have to wait for AC repair, furnace repair, etc., the more difficult you will find it to maintain a comfortable temperature in your residence. Our experienced technicians will find the problem and complete air conditioner or furnace repair quickly. Instead of having to suffer through a cold winter or hot summer due to HVAC problems, contact Deljo Heating & Cooling.

We provide plumbing service to Atlanta and the surrounding communities, including: Acworth, Alpharetta, Austell, Avondale Estates, Brookhaven, Buford, Chamblee, Clarkston, Conyers, Cumming, Dacula, Decatur, Doraville, Douglasville, Duluth, Dunwoody, Fayetteville, Forest Park, Grayson, Holly Springs, Johns Creek, Kennesaw, Lawrenceville, Lilburn, Lithonia, Loganville, Marietta, Milton, Morrow, Norcross, Peach Tree City, Pine Lake, Powder Springs, Roswell, Sandy Springs, Snellville, Stone Mountain, Sugar Hill, Suwanee, and Woodstock, GA.
The contactor (relay) and start/run capacitor(s) (see illustration below) fail most often and are inexpensive. So it’s a safe bet to buy and install those parts right away, especially if your air conditioning service unit is older than five years. The condenser fan motor can also fail, but it runs about $150 — hold off buying that unless you’re sure that’s the culprit.
Installation—Having your HVAC systems installed by a professional is extremely important to prevent any future problems or needless repairs. Our professionals at Service Experts Heating & Air Conditioning can also help you choose what size equipment is appropriate for your house. Selecting a system that is too large or small can impact efficiency and add to your energy bills.
We are open from 7am to 10pm every weekday and from 7am to 8pm on weekends. We book appointments in a 2 hour arrival window and call 30-45 mins before we arrive so you do not have to sit around waiting. It is often possible to schedule your appointment in the evening or morning hours to avoid conflicting with your work schedule. Are you looking for service today? Give us a call or click on one of the Schedule Service buttons found on the top and left sides of this page to contact us today.

The cost to replace your entire unit is around $4,000. That expense can range from $2,500 to $5,900, depending on the type and brand of furnace you choose. Brands particularly have an impact on that price. A Goodman electric furnace, will only cost about $2,100 for the unit and labor. On the other hand, a Trane oil furnace may cost up to $9,000 all things considered. Our Furnace Installation Cost Guide can give you a better idea on both the general cost and the differences for brands like Amana, Bryant, Coleman, and others. The brand also plays into the repair cost for your furnace. Especially the prices of individual parts can change; a York heat exchanger, for example, can cost up to $1,900, while the same component from Heil will cost as little as $400.

HVAC Repair Co

×