Reinstall the access panel and disconnect block. Turn on the circuit breaker and furnace switch. Then set the thermostat to a lower temperature and wait for the AC to start (see “Be Patient at Startup,” below). The compressor should run and the condenser fan should spin. If the compressor starts but the fan doesn’t, the fan motor is most likely shot. Shut off the power and remove the screws around the condenser cover. Lift the cover and remove the fan blade and motor (photo 7). Reinstall the blade and secure the cover. Then repower the unit and see if the fan starts. If it doesn’t, you’ve given it your best shot—it’s time to call a pro.

When your heating and cooling system stops working, you need the help of a reliable, experienced, local service professional that can diagnose the problem and repair your air conditioner or furnace at a fair price. You can count on The Home Depot's licensed and insured heating and cooling professionals for all your heaters, air conditioning units, and any ventilation needs.

Replacing a capacitor is easy. Just take a photo of the wires before disconnecting anything (you may need a reference later on). Then discharge the stored energy in the old capacitor (Photo 4). Use needle-nose pliers to pluck one wire at a time from the old capacitor and snap it onto the corresponding tab of the new capacitor. The female crimp connectors should snap tightly onto the capacitor tabs. Wiggle each connector to see if it’s tight. If it’s not, remove the connector and bend the rounded edges of it so it makes a tighter fit on the tab. When you’ve swapped all the wires, secure the new capacitor (Photo 5).


Attic Fan Installation Bathroom Fan Repair Ceiling Fan Installation Ceiling Fan Repair Electric Wall Heater Installation Electrical Panel Installation Electrical Panel Repair Electrical Panel Upgrade Electrical Wiring Installation Electrical Wiring Upgrade Exhaust Fan Installation Holiday Lighting Installation LED Interior Light Conversion Light Fixture Installation Light Fixture Repair Light Fixture Replacement Light Switch Installation Outlet Installation Outlet Repair Spa Wiring Installation
AC air handler squealing or grinding noises. Though most air handlers have direct-drive motors, some older units may be belt-driven. Squealing sounds from a belt-drive air handler generally occur when the belt that connects the motor to the blower slips. In most cases, the belt is improperly aligned or worn and needs replacement. Follow the instructions above under Air Conditioner Not Blowing Air and refer to your owner’s manual.
Hillsboro, OH ServicesReal Estate Appraisal Services Hillsboro, OHWindow Repair & Maintenance Hillsboro, OHVinyl Flooring Installation Hillsboro, OHStorm Shelter Installation Hillsboro, OHPest Control Contractors Hillsboro, OHMetal Workers & Welders Hillsboro, OHHillsboro, OH Custom Furniture MakerStructural Engineers Hillsboro, OHWindow Replacement Hillsboro, OHSeptic Tank Repair Hillsboro, OHSiding Contractors Hillsboro, OHWindow Installation Hillsboro OHKitchen Remodeling Hillsboro, OHMove Out Cleaning Hillsboro, OHFoundation Repair Hillsboro, OHHome Building Hillsboro, OHDesign-Build Hillsboro, OHTheener Construction LLCRemodeling Hillsboro OHOhio Valley Log HomesJr Ison ImprovementsMovers Hillsboro OH
At Horizon Services, we strive to go above and beyond for every one of our clients. We offer honest, upfront pricing in writing for every service we provide, as well as flexible scheduling to suit your needs, industry leading warranties, and a 100% customer satisfaction guarantee. When you call on us for heating services, our technicians will arrive on-time, every time. If we're even one minute later than the provided window of time, you don't pay. We understand that dealing with a broken or malfunctioning heating system can be incredibly frustrating. Let us turn your stressful situation into a thing of the past!
Cleaning the debris that builds up on your filters will aid with the flow of air. When your air filter is clogged, your air handler must work harder to compensate for the blockage of air flow. In addition to driving up your utility bill, the reduced air flow through your heating and cooling system can cause your heat exchanger to overheat and shut off too quickly.    
If the condenser coils are clogged, the compressor can overheat and shut down. You’ll experience intermittent periods of minimal cooling, followed by no cooling. Even if you’re “sure” the condenser coils are clean, clean them again. Turn off the power. Flip the air conditioning service and furnace circuit breakers in your main electrical panel to the “Off” position. Next, turn off the power switch right at the furnace or air handler. Then yank the disconnect block (Photo 1) and clean the condenser coils (Photo 2). If the air conditioning service still doesn’t work properly after you’ve cleaned the condenser coils, installed a new filter and opened all the supply vents, proceed with the following repairs.
With colder weather on its way back to Waldorf, furnace and heating repair may not be the first thing you think about, but maybe it should be. Sure, it’s easy for us to sit here and tell you to schedule annual furnace service, but it’s only because we want to help you avoid a heating breakdown during the coldest day of the month in Waldorf. Day or night, our HVAC experts are here to make sure you have a comfortable home, and can help get your furnace back running in little time.
Get an accurate price for your HVAC repair costs by contacting a local heating and cooling company and scheduling an inspection. Search HVAC.com’s Contractor Directory to find local HVAC contractors who perform heating and cooling repairs. Call for service and find the price of the HVAC repair costs needed to get your system back into good working order! HVAC Repair Click Here
×