This information is not intended as an offer to sell, or the solicitation of an offer to buy, a franchise. It is for information purposes only. Read More Currently, the following states regulate the offer and sale of franchises: California, Hawaii, Illinois, Indiana, Maryland, Michigan, Minnesota, New York, North Dakota, Oregon, Rhode Island, South Dakota, Virginia, Washington, and Wisconsin. If you are a resident of or want to locate a franchise in one of these states, we will not offer you a franchise unless and until we have complied with applicable pre-sale registration and disclosure requirements in your state. Read Less Aire Serv is a registered trademark of Aire Serv LLC © Aire Serv | All rights reserved | All Aire Serv franchise locations are independently owned and operated.
A heat pump is an appliance used to provide heating and cooling services in moderate climates. These pumps don't generate heat; instead, they move heat from one place to the next, and in so doing, they're able to heat and cool your home at a lower cost. Air-source heat pumps are the most commonly used models on the market. Other choices include water-source and geothermal heat pumps.
Ductwork pinging or popping. If you hear a pinging or popping sound coming from metal ductwork, this may be caused by thermal expansion or by air blowing past a loose flap of metal. Track along the duct runs, listening for the sound. If you find it, make a small dent in the sheet metal to provide a more rigid surface that’s less likely to move as it heats and cools.
Put simply, any home that uses air pushed through ductwork for heating purposes takes advantage of forced air heating. In other words, this term refers not to your furnace, but to the delivery method of the heat throughout your home. Forced air heating is possible with electric or gas furnaces, or a heat pump. Any issues with this delivery system that aren't directly related to the furnace likely have to do with the duct work, which costs between $35 and $55 per linear square foot to repair, or the air handling unit.
"LIFESAVER! Came right out to our home to save us from the heat. I called around 11 and they sent someone by the afternoon 1:30. Carlos fixed our AC on the spot! Very professional and knew what the issues were and fixed them all as fast as possible! Otherwise we would all be toast in this Texas Summer HEat. Thank you Carlos with Ruben's AC! Excellent service"
A contactor is a $25 mechanical relay that uses low-voltage power from the thermostat to switch 220-volt high-amperage current to the compressor and condenser fan. AC contactors can wear out and are at the top of the list of common air conditioning service failures. Even if your contactor is working, it pays to replace it every five years or so. Unscrew the old contactor before removing the wires. Then move the wires to the new unit (photo 6).
Advice you can count on – When you have an emergency, you are not always in the position of asking questions to determine if the repairs you are receiving are what you need. At Jennings, our NATE Certified technicians will walk you through the repairs and explain why you need them. You can trust that everyone on Jennings’ staff will give you honest advice.
Heat pumps don’t discharge air that is as hot as the air discharged by oil or gas forced-air furnaces, so don’t expect their output to feel like that of a furnace. But if you’re used to a certain temperature of air and your heat pump is producing much cooler air, take the following steps. (Note that a heat pump may go into a defrost mode to prevent icing up. When this happens, it can temporarily output cold air. Also be aware that the heat pump will have to work harder to produce heat.

2 Be sure the heat pump is receiving power. The two circuit breakers that protect the electrical circuits providing power to the air handler and heat pump condenser may have tripped. Check both the main electrical panel and any subpanels that supply power to the unit. If either circuit breaker has tripped, reset it by flipping it to OFF and then to ON. If the circuit breaker trips again, there is probably a short in the electrical system providing power to the furnace. Call an electrical contractor (Go to HomeAdvisor).
A heat pump is an appliance used to provide heating and cooling services in moderate climates. These pumps don't generate heat; instead, they move heat from one place to the next, and in so doing, they're able to heat and cool your home at a lower cost. Air-source heat pumps are the most commonly used models on the market. Other choices include water-source and geothermal heat pumps.
We don’t fit the Monday through Friday, 9a.m.-5p.m. schedule. 43% of problems for heating and air conditioning system occur after 5 p.m. To compensate for this, we have more accommodating service hours. We can schedule air conditioning service appointments as late as 11 p.m. This makes it easier for you. We also offer what a lot of heating and air conditioning repair companies don’t; appointments available on weekends.
Finally, don't underestimate the thermostat as a potential reason why your furnace is not working. Everything on the heating unit itself may function perfectly, but your home still will not heat right if the console you use to set the temperature doesn't communicate your input. A faulty thermostat can either be due to the wall unit itself, or the wiring that connects it to your furnace. Average thermostat repair costs are between $108 and $282, including labor. Replacement costs, of course, depend on the thermostat you choose. Visit our thermostat repair cost guide to learn more about this type of issue.

Answering the severe weather swings of the Brownsville, Connellsville, Masontown, Perryopolis, Smithfield & Uniontown, PA area, we bring our customers the most sophisticated and economical solutions to home temperature control. We remain dedicated, not only to the complete satisfaction of local homeowners and businesses, but also to providing environmentally responsible options.

The national average for furnace replacement is between $1,800 and $2,500. The cost can range dramatically higher depending on the model of furnace you select, any repair work you require, your location and the cost of installation. Furnace installation costs can be more than the furnace itself due to the cost of doing business and the expertise needed to install the HVAC equipment. Installing a new furnace generally requires technical know-how and the proper tools and licensing. It’s best to hire a pro and budget for furnace installation rather than risk potentially unsafe DIY installation. This will ensure your home’s safety. Check to see if your HVAC contractor has the proper licensing to do the job. If you need duct repair or replacement, expect to pay more for your furnace installation costs. The price for duct repair could be an hourly rate ranging on average anywhere from $85 to $150 per hour, with additional costs for parts.
×