Our skilled technicians can install a new system quickly to ensure maximum comfort in your home. Utilizing the latest technology, we can calculate the correct size and efficiency for your home. If you would like to upgrade your heater due to safety or reliability concerns, we can help you choose from a wide variety of top-quality heating products with extended warranties offering up to 10 years of coverage.
Have you noticed that your A/C isn’t working as well as it could be? Perhaps there is an unexplained noise coming from the unit, or it doesn’t keep your home at the correct temperature. In these circumstances, a competitively priced repair is vital. It’s unlikely the problem will resolve on its own, so if you suspect there’s an issue, one call to us is all it takes.

If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
In addition to the information below, see these two articles for the general care and maintenance of your air conditioner: Preparing Your Air Conditioner for Summer and How to Replace Furnace & AC Filters. Most noteworthy, you should replace the filters at least twice a year, before the heating and cooling seasons. For information on furnace problems, please see Furnace Not Working.
Reinstall the access panel and disconnect block. Turn on the circuit breaker and furnace switch. Then set the thermostat to a lower temperature and wait for the AC to start (see “Be Patient at Startup,” below). The compressor should run and the condenser fan should spin. If the compressor starts but the fan doesn’t, the fan motor is most likely shot. Shut off the power and remove the screws around the condenser cover. Lift the cover and remove the fan blade and motor (photo 7). Reinstall the blade and secure the cover. Then repower the unit and see if the fan starts. If it doesn’t, you’ve given it your best shot—it’s time to call a pro.

2 Be sure the heat pump is receiving power. The two circuit breakers that protect the electrical circuits providing power to the air handler and heat pump condenser may have tripped. Check both the main electrical panel and any subpanels that supply power to the unit. If either circuit breaker has tripped, reset it by flipping it to OFF and then to ON. If the circuit breaker trips again, there is probably a short in the electrical system providing power to the furnace. Call an electrical contractor (Go to HomeAdvisor).
Air duct cleaning is done by heating, ventilation and air conditioning (HVAC) professionals. The pros use industrial-strength, truck-mounted vacuums and powerful brushes and hoses to clean inside the metal ducts that make up your forced air heating and cooling system. The Environmental Protection Agency recommends duct cleaning if there is “substantial visible mold growth inside hard surface ducts, ducts that are infested with vermin such as rodents or insects, or ducts that are clogged with excessive amounts of dust and debris and/or particles are actually released into the home from your supply registers.”
When I came to Home Depot to put my order for reparing my furnance, the representive said diagnosis is free.But Blue Flame charge me $80. It is probably the transformer failure. The transformer was changed one year ago. The part Blue Flame installed is made in China and sell online $10/each. Blue Flame charges $385, including installation. That's over charged
Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.
While repair is often the preferred choice, problems like a consistent repeating complication or extra-costly furnace repair parts might start leading you in a different direction. Remember that repair is only the preferred option when the cost of seeking it makes sense! If you’re shelling out for repair every single year, then it might be time to talk to your heating contractor about furnace replacement.
Deljo Heating & Cooling is also a Mitsubishi Diamond Dealer, guaranteeing a superior skill set, dedicated customer service and sophisticated solutions to the most challenging home temperature concerns. Our technicians participate in extensive training and education at every level of service, from new product sales to continued customer care, at a Mitsubishi Electric-approved training center. Through intensive training and years of firsthand experience, our HVAC....

If you happen to live in a hot and humid area of the country, drainage problems can occur with your unit since moisture can trap itself inside the system. Routine maintenance can cut down on drainage issues by cleaning out any mold or algae from blocking the drain. If you notice moldy smells whenever you turn the thermostat down, check on your system.

It’s important to keep your furnace receives regular maintenance to ensure that it’s working properly and efficiently. Routine maintenance can also extend the life of your heating system by several years. Ask about our annual maintenance agreements that cover your plumbing, heating, and cooling systems and save you money. A furnace that has been neglected may be working too hard, which can result in inconsistent air temperatures in your Minneapolis area home. Learn more about the importance of routine maintenance on your HVAC system.
No one wants to be stuck in the dead of summer with a broken air conditioner, or in the cold of winter with a broken furnace or boiler. That’s why we’re available any time of day to make your emergency heating and air conditioning repair and get your system up and running as quickly as possible. We’ll show up on time, in uniform and ready to make your HVAC repair right the first time.
B & B Heating & Cooling offers furnace service appointments that help keep your furnace in excellent shape and running efficiently for you all year long. Whether that’s finding small issues before they become big problems, identifying potential safety hazards or making sure you’re staying in line with your manufacturer’s warranty, our experts have you covered. Our trained technicians complete furnace service with care, inspecting a number of components in and around your furnace. In fact, our multi-point inspection can help make sure your system runs smoothly throughout the winter.

We provide plumbing service to Atlanta and the surrounding communities, including: Acworth, Alpharetta, Austell, Avondale Estates, Brookhaven, Buford, Chamblee, Clarkston, Conyers, Cumming, Dacula, Decatur, Doraville, Douglasville, Duluth, Dunwoody, Fayetteville, Forest Park, Grayson, Holly Springs, Johns Creek, Kennesaw, Lawrenceville, Lilburn, Lithonia, Loganville, Marietta, Milton, Morrow, Norcross, Peach Tree City, Pine Lake, Powder Springs, Roswell, Sandy Springs, Snellville, Stone Mountain, Sugar Hill, Suwanee, and Woodstock, GA.
With a modern heat pump system installation, you’ll enjoy benefits such as exceptional efficiency and maximum temperature control all year round. These innovative systems combine both heating and cooling into one compact system. The technicians from Sky Heating & Air Conditioning are highly qualified and experienced in heat pump maintenance, repairs, and installations, so you can feel confident in our services. We specialize in WaterFurnace geothermal heat pump systems, which offer unprecedented efficiency and energy savings. Browse our website or give us a call today to learn even more!

Interesting article but I feel you should give it more depth. When you write about foundations, you only mention poured concrete like there is no other type. Some houses have foundations made with brick, masonry block and less commonly stone. Same comment for roofing type. Never heard of a flat roof? Binoculars won't work for that type. Also, you should point out that the owner of a house can provide information that can't be directly observed like the age of a roof (but can be confirmed later with a home inspection).
When your furnace isn’t regularly serviced it can operate less efficiently. This increases your energy bills and also prevents your furnace from keeping your home as warm as you like. Keep your furnace properly maintained with regular service. The national average furnace service cost is between $60 and $80. Companies may offer tuneup specials that cover all the necessary testing, tightening, measuring and cleaning to keep your equipment running at top efficiency. If you have a newer system, furnace service costs may be covered by your warranty. Outside of warranty, a basic tuneup might start at $58 and a more advanced maintenance cleaning could be over $120. Here are some signs your furnace may need service:
×