If you happen to live in a hot and humid area of the country, drainage problems can occur with your unit since moisture can trap itself inside the system. Routine maintenance can cut down on drainage issues by cleaning out any mold or algae from blocking the drain. If you notice moldy smells whenever you turn the thermostat down, check on your system.
Get an accurate price for your HVAC repair costs by contacting a local heating and cooling company and scheduling an inspection. Search HVAC.com’s Contractor Directory to find local HVAC contractors who perform heating and cooling repairs. Call for service and find the price of the HVAC repair costs needed to get your system back into good working order!
Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.
As a Bryant Factory Authorized Dealer, Cool Care Heating & Air installs durable, high-quality heating systems that will go the distance. Are you considering a heater installation or heating repair? If so, you have found the best HVAC dealer in the Columbia, SC area. We specialize in high-efficiency furnaces, heat pumps and boilers that can cut energy costs month after month.

You should never be faced with your heating system quitting or simply not running at peak performance during bitter cold temperatures. If you do, it’s important to know you have a top heating repair company ready to help.  One Hour Heating and Air Conditioning the top heating contractor in Charlotte for all your heating repair needs. We understand the need for timeliness when the cold sets in—in fact, you could say our company was founded on speed: “Always on Time…Or You Don’t Pay a Dime!”
It can be difficult to find the right company to do Aurora furnace repair and Aurora furnace replacement. When looking for the right help choose an Aurora furnace replacement and repair company that comes recommended and has a strong reputation. As a licensed furnace replacement company in Denver, Brothers Plumbing Heating and Electric has been working on the repair and replacement of furnaces for many years. Furthermore, we have a long list of happy customers that recommend us to all their friends and family.

If you hear clicking that is followed by a hum or buzz, you’re probably hearing the fan motor attempting to start without the boost it needs from the capacitor. You can almost always conclude that the capacitor has failed. Sometimes you can get the compressor fan spinning (clockwise) by pushing it with a thin stick or long screwdriver poked through the grille. But the chances are good that this might work for one cycle, but the capacitor will fail next time the AC goes on. It’s best to replace the capacitor.


Cut down on energy costs and prevent damage to your furnace by addressing a gas furnace that's overactive or short cycling. Besides the need for consistently comfortable temperatures, this issue could cause long-term safety issues to your home, making it very important to address. From a faulty thermostat to a dirty filter, there are several possible causes to investigate.
Put simply, any home that uses air pushed through ductwork for heating purposes takes advantage of forced air heating. In other words, this term refers not to your furnace, but to the delivery method of the heat throughout your home. Forced air heating is possible with electric or gas furnaces, or a heat pump. Any issues with this delivery system that aren't directly related to the furnace likely have to do with the duct work, which costs between $35 and $55 per linear square foot to repair, or the air handling unit.

Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.
If the air conditioner on your thermostat set low, and you aren't feeling cool air, it could be that debris is blocking the condenser. Check on your system outside and remove any tree branches or leaves from around it. Debris can easily obstruct air flow, so make sure the area around your air conditioning unit is clean and trimmed back. Make sure your filter is clean. A buildup of dirt and dust can cause poor air circulation.
To reset a gas furnace, start by making sure the pilot light has been extinguished. Next, turn down the room thermostat to its coldest setting, and cut the furnace's power from your home's circuit breaker. Cut the main gas supply to the furnace, but make sure that the gas line that leads to the furnace pilot is on. Light a match, and use it to ignite the jet of the furnace's pilot flame. Then restore the furnace power and main gas supply, and press and hold the furnace reset button for roughly half a minute.

A: When experiencing this problem, your first step should be changing the air filter and see if your furnace starts blowing warm air. DO NOT ignore this issue. Long term overuse will hurt your furnace heat exchanger, which is an expensive fix. Another possible option if you have a gas furnace is checking the pilot light to make sure it did not go out.
Consequently, this water must exit the air handler—typically through plastic pipe or a drain tube. That drain tube goes directly outside, often terminating near the compressor, or to a floor drain or to a small electric “condensate pump” located by the air handler. Where a condensate pump is used, it connects to a 1/2-inch vinyl or rubber tube that exits outdoors or to a drain.
Geothermal Heating and Cooling systems are unmatched in every way. This green alternative to temperature control is three times more efficient than conventional systems. Recognized by the US Environmental Protection Agency as the most environmentally-friendly option available today, installation of a geothermal HVAC system translates into a 50% reduction in heating costs, 30% reduction in cooling costs, and a 65% potential savings on hot water costs.  Sky Heating & Air Conditioning is now the largest WaterFurnace geothermal contractor west of Iowa. Our team of experienced professionals offer conscientious and skilled start-to-finish installation and service.  We specialize in outstanding geothermal HVAC systems, adding value and enjoyment to your home through sustainable solutions to year round temperature control. Contact Sky Heating & Air Conditioning for geothermal heat pump installation in Portland.
No matter how well you take care of your system, there will come a time when it simply runs out of gas. When your heater cannot be restored with repair work, our team will replace your old system with a new, energy-efficient unit. Working with all makes and models, our comfort specialists have access to the most superior, affordable and effective heating systems on the market.
Feel perfectly comfortable at home with our innovative Lennox Residential heating, cooling and air quality systems. Lennox manufactures high-efficiency HVAC systems including furnaces and air conditioners designed to conserve energy and save money. Our complementing air filtration systems, humidifiers and dehumidifiers help keep indoor air quality healthy and clean.

About us: Vredevoogd Heating & Cooling has been in business since 1964. As a financially stable company known for its reliable expertise and first-rate customer care, Vredevoogd Heating & Cooling is a company you can trust. Moreover, when you do business with a stable business like Vredevoogd Heating & Cooling, you have the peace of mind of knowing that your warranties are solidly backed by a company that intends to remain in business for another 50+ years and beyond. Don’t trust your essential home systems and investment to any fly-by-night company. Our best practices ensure that we will be here to meet our customer’s HVAC needs for decades to come. Vredevoogd Heating & Cooling founder Dennis Vredevoogd set the high standards by which the company continues to pride itself for. Today, the company continues to be family owned and operated by the founder’s sons, Michael and Thomas, who are committed to maintaining the company’s high standards and complementing them with the innovative technical know-how needed to service today’s advanced HVAC systems.
Brothers Plumbing, Heating, and Electric came to the rescue. Our furnace was operating erratically over the Thanksgiving holidays. Brothers made time for us during this busy heating season to address and fix the problem. The heating technician, Ron, was thorough in explaining every diagnostic step he was taking in solving the problem. We appreciate the excellent service he provided us.
If your furnace needs to be repaired, you’ll want to find a qualified heating, ventilating and air conditioning (HVAC) repair technician. Each state has its own licensing requirements; some require all HVAC technicians to have an HVAC license, while others only require someone operating an HVAC service and installation company with employees to hold a contractor’s license. For example, in Alabama, the Alabama Board of Heating Air Conditioning, and Refrigeration Contractors regulates licensing, while in Kansas there is no state regulatory body and HVAC licensing can vary by region. For simple furnace repairs like changing out a filter, a trusted handyman can probably handle the job, but a trained professional should be hired for tasks like replacing a gas valve, installing a new inducer fan motor or other critical furnace repair jobs that involve dealing with gas leaks or other dangerous conditions. For more, check out our tips for smart hiring on Thumbtack.
×