In addition to the information below, see these two articles for the general care and maintenance of your air conditioner: Preparing Your Air Conditioner for Summer and How to Replace Furnace & AC Filters. Most noteworthy, you should replace the filters at least twice a year, before the heating and cooling seasons. For information on furnace problems, please see Furnace Not Working.
Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.
There’s nothing like a warm indoor space to take the sting out of a blustery winter day, but there’s nothing worse than a heater that quits just when you need it most. Losing heat for any length of time can be inconvenient at best and dangerous at worst. Fortunately, when you partner with Cool Care Heating & Air, you can rest assured that whether you need emergency heating repair or annual furnace maintenance, we’ll go all out to keep you comfortable. Cool Care Heating & Air is a Bryant Factory Authorized Dealer, so you can always count on prompt service, a courteous attitude, reasonable prices and top-shelf products.
In addition to providing repairs for A/C and HVAC systems, we can also repair almost any heating system. Just tell us what the trouble is and we will run the appropriate tests and checks to find out what needs doing to get your heating operational again. We use high-grade equipment and tools for every job we complete, helping to give you the top-quality results you’re looking for.
If the power to the heat pump goes out, be aware that most heat pumps have auxiliary heating elements that provide heat when the weather gets really cold and the heat pump’s efficiency drops too low. These elements automatically turn on at a fairly low temperature—around 20 degrees F. When they come on, they may be drawing too much power, which can trip the circuit breaker. Just locate the circuit breaker that serves the heat pump and reset it.
Repairs—If something appears to be not working right with your heating and cooling, a professional will examine the whole health of your system. It’s easy to hop on the internet and research information to find our own conclusions, but there could be an additional component or reason why your system isn’t working properly that isn’t clear or recognizable. Consider our own health concerns—you might check out your symptoms online to try and draw your conclusions, but it’s always best to make an appointment with a doctor to receive an expert opinion.
I have a 90% efficient forced air gas furnace and when it was installed 4 years ago the guy didn't hook up a fresh air intake pipe allowing the furnace to draw in air from the hallway(slab home). My question is there are two holes for intake and I need to know if I should use one for the intake and block off the other or does it require two pipes? There is already a 2 exhaust leading outside thru wall.
We’ve proudly represented the very best Atlanta has to offer in superior service for 50 years. In that time, we’ve accumulated all it takes and more to bring you the best emergency heating and air conditioning repair services possible. Story after story, we deliver smiles! If you’re looking for a reliable company that provides 24-hour AC repair, don’t hesitate to contact us right away—770-913-6412!
If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
In order to make your everyday life easier and more enjoyable, Sky Heating & Air Conditioning specializes in state-of-the-art heating and cooling technology, partnering with Trane, Mitsubishi, and Waterfurnace.  We bring you HVAC solutions that represent the best the industry has to offer, ensuring long-term performance and satisfaction.  Whether you’re looking for the design/build of a new system, replacement, or hoping to cut costs and enhance convenience, we answer with proven products.  Our qualified HVAC technicians help you determine the ideal solution for your exact requirements, and make sure you’re happy with every step of the process.  From ductless HVAC to geothermal heating and cooling systems, we offer a wide selection of options and comprehensive services to answer any type of challenge.  Call on Sky Heating & Air Conditioning and let us exceed your expectations today!
Let Fayette Furnace help you step up your home efficiency with a wide range of air conditioning and heating products, services and our skilled team of technicians. An employee owned company since 1920; we pride ourselves on continuing a longstanding tradition of honesty, professionalism and expertise. Call and ask about our service maintenance agreements to save money on maintenance and emergency calls.
Any forced air system in your home - whether it is powered through electric or gas-generated energy - requires a blower motor. This component consists of an electric motor and fan, and is responsible for pushing air evenly through the furnace. As hvac.com points out, you can easily identify the blower motor in your furnace as the part that looks similar to a hamster wheel at the bottom of the unit. If it stops working, the air needed to heat your home will no longer be pushed through the furnace to be heated and distributed evenly. In that case, you need to inquire about potential repairs. Blower motor repair typically costs between $150 for a simple fix, and $450 for complete replacement and installation of the part. Where you land on that range depends on the exact damage.
Replacing a capacitor is easy. Just take a photo of the wires before disconnecting anything (you may need a reference later on). Then discharge the stored energy in the old capacitor (Photo 4). Use needle-nose pliers to pluck one wire at a time from the old capacitor and snap it onto the corresponding tab of the new capacitor. The female crimp connectors should snap tightly onto the capacitor tabs. Wiggle each connector to see if it’s tight. If it’s not, remove the connector and bend the rounded edges of it so it makes a tighter fit on the tab. When you’ve swapped all the wires, secure the new capacitor (Photo 5).
At Genz-Ryan, we are here for you 24 hours a day, 7 days a week so you can count on us for all your heating repair work in the Minneapolis area. Our furnace repair technicians are well-trained and experienced. They’re ready to take care of any heating issue that you may have. We are a Lennox Premier Furnace Dealer and provide expert furnace repair service for most of the Minneapolis/St. Paul area. For over 60 years we have been getting the job done right the first time.
Many disconnect blocks contain two cartridge fuses. Check them before you proceed with repairs (Photo 3). A blown fuse is a sign of a failing part inside the condensing unit. So don’t just replace it and think you’ve solved the problem. Instead, replace the parts we show here. Then install new fuses and fire up the unit. If it blows again, call a pro—you’ve got more serious issues.
Furnaces and thermostats are not mix-and-match appliances. Using the wrong type of thermostat with a furnace will cause operating problems and can be dangerous. Although thermostats look similar, they are designed very differently. There are numerous types of heating systems and thermostat systems and they need to be coordinated for safe and proper operation. There are three types of thermostat systems used today: millivoltage, low voltage, and line voltage.​
When your furnace filter becomes dirty, dusty and clogged, you can expect some negative effects on your furnace efficiency and your indoor air quality. The forced air is supposed to get blown through the filter and the filter is supposed to trap any particles so they don’t end up in your air ducts and throughout the house. When the filter has trapped too many particles and it is clogged up, the air keeps blowing, but some of those trapped particles will end up in the system and your living space. Another effect is that the furnace has to work harder to get the same amount of air through that dirty filter, so your heating bills may go up.
Need 24-hour emergency furnace repair? We can provide that too. With our same-day service and live phone and online chat service available 24/7, we make your comfort our greatest priority. Heating and air conditioning should help you live a comfortable life, so let us help you make your home the most comfortable it has ever been. It’s easy, just grab your furnace repair coupon, then simply give us a call at 301-747-3140, chat or schedule an appointment with us online.
Replacing a capacitor is easy. Just take a photo of the wires before disconnecting anything (you may need a reference later on). Then discharge the stored energy in the old capacitor (Photo 4). Use needle-nose pliers to pluck one wire at a time from the old capacitor and snap it onto the corresponding tab of the new capacitor. The female crimp connectors should snap tightly onto the capacitor tabs. Wiggle each connector to see if it’s tight. If it’s not, remove the connector and bend the rounded edges of it so it makes a tighter fit on the tab. When you’ve swapped all the wires, secure the new capacitor (Photo 5).

New heating and cooling equipment installations present a wide variety of options that can save you money on your power bills and reduce the amount of HVAC maintenance and service that will ultimately be required over the life of your new unit. Energy-efficient options like heat pumps, two-stage furnaces, air-to-heat exchangers (HRVs), and programmable thermostats can all go a long way toward increasing efficiency and extending the life expectancy of your system.
AC air handler squealing or grinding noises. Though most air handlers have direct-drive motors, some older units may be belt-driven. Squealing sounds from a belt-drive air handler generally occur when the belt that connects the motor to the blower slips. In most cases, the belt is improperly aligned or worn and needs replacement. Follow the instructions above under Air Conditioner Not Blowing Air and refer to your owner’s manual.
Not to mention, John Betlem offers emergency services, too, so you and your family won’t have to suffer in the cold for long if your furnace breaks down. What’s more, when you have a service agreement with us, we’ll give you priority service – we’ll put you to the top of our list for your emergency furnace repair, even during our busier times. When you have a service agreement, you’ll get an annual tune-up, too – and that makes it less likely that you’ll need emergency furnace repairs.
Our skilled technicians can install a new system quickly to ensure maximum comfort in your home. Utilizing the latest technology, we can calculate the correct size and efficiency for your home. If you would like to upgrade your heater due to safety or reliability concerns, we can help you choose from a wide variety of top-quality heating products with extended warranties offering up to 10 years of coverage.

*We work on all brands: Adams, Aire-Flo, Amana, Arcoaire, Armstrong, Beutler, Bryant, Carrier, Centurion, Coleman, Comfortmaker, Cozy, Daikin, Day & Night, Dayton, Ducane, Emerson, Empire, Evcon, Fedders, Friedrich, Frigidaire, Fujitsu, Gaffers & Statler, General Electric, Gibson, Goldstar, Goodman, GMC, Haier, Heil, Honeywell, Intertherm, Janitrol, Kenmore, Lennox, Luxaire, Maytag, Mitsubishi, Payne, Rheem, Ruud, Samsung, Sanyo, Sears, Sharp, Spartan, Tappan, Tempstar, Thermal Solutions, Trane, Utica, Weatherking, Westinghouse, Whirlpool, Williams, York, and Zephyr.
I have a 90% efficient forced air gas furnace and when it was installed 4 years ago the guy didn't hook up a fresh air intake pipe allowing the furnace to draw in air from the hallway(slab home). My question is there are two holes for intake and I need to know if I should use one for the intake and block off the other or does it require two pipes? There is already a 2 exhaust leading outside thru wall.

Yes. You should expect to pay a diagnostic fee to cover the cost of the technician's visit, the diagnosis of your air conditioner's problem, and a quote for the repair options. You will be advised of the issue along with recommended options to correct it, which may include a system replacement if your unit is old or significantly damaged. If you decide to replace the system, the diagnostic fee will be credited toward your replacement purchase.


Vredevoogd Heating & Cooling stands behind its services and products with the strongest guarantees you’ll find anywhere. When you invite us into your home to service or install your HVAC system or do Furnace Repair work in Grand Rapids and beyond, we perform our job with an outstanding level of care and efficiency. Having served Michigan for 54 years, we never rest on our laurels. To remain the best, we intend to give our best every time, every job.
The main purpose of your furnace filter is to ensure that none of the additional materials your fans pull back into the unit - such as hair and dust - actually damage the furnace or its parts. In the process, it also improves air quality in your home. Some annual inspections will include changing and cleaning this part of the unit. That said, you can also clean or change your furnace filteryourself. Costs for new filters range based on brand, but tend to be around $30.

Be cautious with companies that offer “whole house air duct cleaning,” urges the NADCA. The company may be using unscrupulous tactics to upsell you once they get started. Before any work begins, always clarify in writing what the job entails and what the cost will be. To protect yourself against fraud, read customer reviews and verify that your HVAC cleaning service has applicable licenses and certifications.
At Sky Heating & Air Conditioning, we understand that HVAC services can really hurt your budget. Many times, you don’t expect to make such large purchases until an emergency arises. We never want you to feel that you cannot afford your comfort and safety. We offer flexible financing options through the Home Project credit card from Wells Fargo, with approved credit. Head over to our financing page to apply, or give us a call for more information!
Ultimately, the cost to repair your furnace depends on a wide range of variables. From the brand of the units to the damaged or broken parts, you need a reliable and trusted professional who can evaluate the issue and recommend next steps. If you're unsure whether to repair or replace your furnace, or even where to begin, connect with a local furnace repair professional who can make sure that your home heats well both now and in the future.
Your comfort is a priority for us. A large part of comfortable living in Cary is not only having a functioning HVAC system, it’s also understanding who to call when you have a problem. If your air conditioner starts to fail in the middle of the Cary summer, you don’t have to stay at a friend’s for weeks on end. Or if your heater goes out during a blizzard, you don’t have to dig your heaviest blankets out of the basement. Instead, you can make an appointment with a member of our team and have him or her resolve your concerns. There is no problem in Cary you can encounter that we can’t work with you to solve. You can feel confident in knowing that you’re in qualified hands.
You can keep your air conditioner running efficiently with some preventative care measures. Shut off the power to your AC before cleaning it or performing any of these tasks:  clean your filter at least twice a year; remove leaves and twigs from cages; clean the fins with a garden hose or special spray, then use a butter knife to straighten any that are crooked; keep your yard clean so the fins won't get blocked; cover the unit up for winter; and make sure it's level or you run the risk of damaging the inner workings of the unit.
We’re located in Florissant and service the surrounding area, so feel free to swing by if you’re searching for a new furnace or want to set up an appointment to have one of our techs visit your home and help you figure out which system is ideal for your home. Schedule furnace repair or a furnace service appointment with B & B Heating & Cooling using our online scheduler, or if you’re in need of help a little more quickly, give us a call at 314-838-9800. 
When your furnace filter becomes dirty, dusty and clogged, you can expect some negative effects on your furnace efficiency and your indoor air quality. The forced air is supposed to get blown through the filter and the filter is supposed to trap any particles so they don’t end up in your air ducts and throughout the house. When the filter has trapped too many particles and it is clogged up, the air keeps blowing, but some of those trapped particles will end up in the system and your living space. Another effect is that the furnace has to work harder to get the same amount of air through that dirty filter, so your heating bills may go up.
Need 24-hour emergency furnace repair? We can provide that too. With our same-day service and live phone and online chat service available 24/7, we make your comfort our greatest priority. Heating and air conditioning should help you live a comfortable life, so let us help you make your home the most comfortable it has ever been. It’s easy, just grab your furnace repair coupon, then simply give us a call at 301-747-3140, chat or schedule an appointment with us online.

Furnace Repair Company

×