If you believe that the ac not working or you’re getting little or no cold air, check these three things first. Make sure all the registers in the house are wide open. Then be sure the furnace filter is clean. Then go outside and clean off the condenser coils (Photo 2). If several registers were closed or the filter was clogged, the reduced airflow could have caused the evaporator coil to ice up and stop cooling your home. If you’ve changed the filter and opened all the registers and you’re still not getting airflow at the registers, deice the A-coil. Move the thermostat mode switch from “Cooling” to “Off” and move the fan switch from “Auto” to “On.” Let the blower run for at least 30 minutes or until there’s good airflow at the registers. Then turn the AC back on to test it. If it works for the next 12 hours, you’ve solved the problem.
Not to mention, John Betlem offers emergency services, too, so you and your family won’t have to suffer in the cold for long if your furnace breaks down. What’s more, when you have a service agreement with us, we’ll give you priority service – we’ll put you to the top of our list for your emergency furnace repair, even during our busier times. When you have a service agreement, you’ll get an annual tune-up, too – and that makes it less likely that you’ll need emergency furnace repairs.

Smyrna homes and businesses have relied on Coolray for air conditioning service and installation since 1966. We can provide repair and maintenance on all makes and models of air conditioners for your home or business and offer 24 hour emergency AC repair service. We also offer a wide range of new air conditioning systems and our expert air conditioning technicians can help you select an air conditioner or heat pump that is right for your home and budget.
If your home is not heated using forced air, chances are a boiler will make sure you stay warm during cold nights. A hot water system delivers hot water through a network of pipes that run to every room in your house. The heating effect gets maximized through radiators. The most common issues with hot water heating tend to be not be major, but small problems that add up over time. Mineral deposits within the water tank, a pilot light malfunction, or an issue with a radiator itself can require professional repair. On average, you will pay between $183 and $582 for these problems. The exact amount will depend on the exact problem, as described in our boiler repair cost guide.
If your furnace needs to be repaired, you’ll want to find a qualified heating, ventilating and air conditioning (HVAC) repair technician. Each state has its own licensing requirements; some require all HVAC technicians to have an HVAC license, while others only require someone operating an HVAC service and installation company with employees to hold a contractor’s license. For example, in Alabama, the Alabama Board of Heating Air Conditioning, and Refrigeration Contractors regulates licensing, while in Kansas there is no state regulatory body and HVAC licensing can vary by region. For simple furnace repairs like changing out a filter, a trusted handyman can probably handle the job, but a trained professional should be hired for tasks like replacing a gas valve, installing a new inducer fan motor or other critical furnace repair jobs that involve dealing with gas leaks or other dangerous conditions. For more, check out our tips for smart hiring on Thumbtack.
Solar heating is a method where the sun’s energy is collected by panels and converted to reusable energy. The sunlight collected is converted to direct current (DC) by photovoltaic cells in the panels. Then an inverter converts the DC current into alternating current (AC) and the panels send that electricity out and into your home to power things like your TV, computer, game consoles, and air conditioner. The more sunlight you have access to, the more energy you can produce. In some areas, solar powered homeowners can sell or trade the excess power they have accumulated to local power companies.
If you need a furnace repaired or an air conditioner serviced, we'll send a local technician out to diagnose the specific problem and recommend solutions for you and your family. There will be a diagnostic fee for the visit, and any specific repairs will be an additional charge. If replacing your system is the best solution, the fee for the diagnosis will be credited toward the purchase and install of a new system.
Check the thermostat to see if the Fan switch has been turned on. If it has, turn it to OFF or to Auto. If it is set to OFF or Auto already, the heat pump’s limit switch needs to be adjusted. Call a heat pump repair technician to make the adjustment or, if you are handy with this type of repair, follow the instructions in your owner’s manual to reset the pointers on the fan side of the limit control. The lower pointer should be set to about 90 degrees F. and the upper one should be at about 115 degrees F.
If your heat pump does not heat or cool properly, freezes up, or cycles off and on too frequently, this article can help. Following is step-by-step advice for troubleshooting typical heat pump problems and DIY heat pump repairs. Here we will deal with heat pump power problems; freezing up; improper heating, cooling, and cycling; blower issues; noises; and more. If these simple repair techniques don’t work, have a heat pump repair technician (go to HomeAdvisor) check out your system.

Mitsubishi Electric is a world leader in air conditioning systems for residential, commercial and industrial use. Challenged to create air conditioning systems that provide exemplary performance in the wide-ranging climatic conditions found throughout Japan, our engineers develop amazingly sophisticated yet durable units and systems capable of constant use under virtually any natural climatic condition on earth.
No matter how well you take care of your system, there will come a time when it simply runs out of gas. When your heater cannot be restored with repair work, our team will replace your old system with a new, energy-efficient unit. Working with all makes and models, our comfort specialists have access to the most superior, affordable and effective heating systems on the market.

Consequently, this water must exit the air handler—typically through plastic pipe or a drain tube. That drain tube goes directly outside, often terminating near the compressor, or to a floor drain or to a small electric “condensate pump” located by the air handler. Where a condensate pump is used, it connects to a 1/2-inch vinyl or rubber tube that exits outdoors or to a drain.
Central home air conditioner service systems consist of two major components: a condensing unit that sits outside your house, and the evaporator coil (often referred to as an A-coil) that sits in the plenum of your furnace or air handler. The refrigerant in the A-coil picks up the heat from your home and moves it to the outdoor condensing unit. The condensing unit fan blows outside air through the condensing coil to remove the heat. The condensing unit houses the three parts replaceable by a DIYer: the contactor, the start/run capacitor(s) and the condenser fan motor. The condensing unit also houses the compressor, but only a pro can replace that. The A-coil has no parts that can be serviced by a DIYer.
To keep your furnace in good working order it’s important to have it regularly cleaned. The national average furnace cleaning cost ranges from $60 to $80, though prices can vary greatly based on where you live in the country and what your furnace maintenance includes. An HVAC company may have different rates for different levels of furnace maintenance. For example,one company may offer general furnace maintenance for $79 and advanced maintenance for $138. Another company may offer a 38-point maintenance check for $89 and a 64-point maintenance check for $178. According to Energy.gov, a standard furnace cleaning and maintenance visit can include:
×