"Very impressed. Returned call within 24 hours. They came out the same day I spoke with them and made the repair within 25 minutes. Very low service call fee. I had another repair service out two weeks earlier and after 3 service calls and the central air still not fixed and temperatures in the high 90's, it was such a relief to have a company identify the problem, have the necessary part with them and fix the problem."

You can keep your air conditioner running efficiently with some preventative care measures. Shut off the power to your AC before cleaning it or performing any of these tasks:  clean your filter at least twice a year; remove leaves and twigs from cages; clean the fins with a garden hose or special spray, then use a butter knife to straighten any that are crooked; keep your yard clean so the fins won't get blocked; cover the unit up for winter; and make sure it's level or you run the risk of damaging the inner workings of the unit.


If the condenser coils are clogged, the compressor can overheat and shut down. You’ll experience intermittent periods of minimal cooling, followed by no cooling. Even if you’re “sure” the condenser coils are clean, clean them again. Turn off the power. Flip the air conditioning service and furnace circuit breakers in your main electrical panel to the “Off” position. Next, turn off the power switch right at the furnace or air handler. Then yank the disconnect block (Photo 1) and clean the condenser coils (Photo 2). If the air conditioning service still doesn’t work properly after you’ve cleaned the condenser coils, installed a new filter and opened all the supply vents, proceed with the following repairs.
When a family chooses to work with Brothers Plumbing Heating And Electric they will not be disappointed. We are able to work on a very tight schedule and we know just what it takes to service a furnace. There is no doubt about it, a family does well to look into Brothers Plumbing Heating and Electric because we are truly the best Aurora furnace repair company. To learn more about heating and cooling systems, just give this page a visit today!
Before opening the electrical cover on the A/C unit, be sure to shut off all power to the compressor unit and the indoor furnace or air handler, and verify that it is off. Note that this may mean shutting off a circuit breaker that serves the furnace and air handler, and then, near the compressor, pulling out the disconnect block (or shutting off the 220-volt power) to the outdoor compressor.
If your furnace needs to be repaired, you’ll want to find a qualified heating, ventilating and air conditioning (HVAC) repair technician. Each state has its own licensing requirements; some require all HVAC technicians to have an HVAC license, while others only require someone operating an HVAC service and installation company with employees to hold a contractor’s license. For example, in Alabama, the Alabama Board of Heating Air Conditioning, and Refrigeration Contractors regulates licensing, while in Kansas there is no state regulatory body and HVAC licensing can vary by region. For simple furnace repairs like changing out a filter, a trusted handyman can probably handle the job, but a trained professional should be hired for tasks like replacing a gas valve, installing a new inducer fan motor or other critical furnace repair jobs that involve dealing with gas leaks or other dangerous conditions. For more, check out our tips for smart hiring on Thumbtack.
To reset a gas furnace, start by making sure the pilot light has been extinguished. Next, turn down the room thermostat to its coldest setting, and cut the furnace's power from your home's circuit breaker. Cut the main gas supply to the furnace, but make sure that the gas line that leads to the furnace pilot is on. Light a match, and use it to ignite the jet of the furnace's pilot flame. Then restore the furnace power and main gas supply, and press and hold the furnace reset button for roughly half a minute.
Furnaces require routine maintenance in order to maximize performance, maintain efficiency, and ensure safety. Most heating systems should be inspected by an expert every fall to ensure that the system is operating correctly and safely. Our Total Comfort Tune-Up is a professional cleaning, adjustment, and safety check that is performed on all types of heating equipment to help maintain peak performance, safety, and reliable operation.
Our technicians explain all of your options before beginning the repair, so you can decide whether a repair or replacement is best for you. Our No Surprises Pricing—including charging by the job, not by the hour—means the price we quote you is the price you pay. If you decide that replacing your furnace is the best course of action, we can install a new, high-efficiency model in its place.

Advice you can count on – When you have an emergency, you are not always in the position of asking questions to determine if the repairs you are receiving are what you need. At Jennings, our NATE Certified technicians will walk you through the repairs and explain why you need them. You can trust that everyone on Jennings’ staff will give you honest advice.

Today’s heaters are technological wonders that will keep you warm and save you money. Investing in an energy-efficient heating system can raise the value of your property, and the cost of installation will be realized on the amount you’ll save on utility bills. With Cool Care Heating & Air, you can count on proper sizing and a hassle-free installation process. The new unit may also qualify for energy-efficient incentives, and Cool Care Heating & Air offers periodic dealer rebates on select replacement systems. If your heating system is 10-15 years old, needs frequent repair work and isn’t keeping you as warm as it used to, it’s probably approaching the end of its lifespan. Replacing the unit before it dies altogether can save you time, trouble and money.

Furnace Repair

×